122674

Marmitek easytouch 35 Manual

18
Zoom out
Zoom in
Previous page
1/80
Next page
18 MARMITEK
To switch on/ off an appliance plugged into an home control module: Press the
key (2), then press the unit code of the home control module on the Touchscreen
display and then press CHAN+ / - (8).
To dim/bright a light plugged into a home control module: press its unit code on the
Touchscreen display and then press VOL+ / - (4).
To turn ON all the home control Lamp modules: Press the Power key (3).
To turn Off all the home control modules (Lamp and appliance): press the
Mute key (7).
12.1. Changing the home control House Code
The preset house code is A. In the majority of cases it is not necessary to change this
setting except if there is interference from neighbouring Marmitek X10 systems. In that
case:
1. Press the Marmitek X-10 Home Control key
2. Press and hold SETUP until the LED lights continuously.
3. Release the SETUP button.
4. Press the SETUP button again.
5. Use the digit keys on the Touchscreen display to enter the number equivalent to the
chosen home code (1=A, 2=B, ... 16=P).
6. Press ENTER followed by EXIT to confirm your command.
Note: The code you have chosen has to be the same as the one selected on the
Transceiver module TM13 or the security console, with which you use your remote.
12.2. Programming the Home Control IR/RF mode
Your ET35 remote control can control your electrical appliances using infrared signals (via
an infrared mini-controller IR7243) or RF signals (via a transceiver module TM13). The
key is set to RF mode by factory setting.
To program the key to send an Infrared signal, proceed as follow
1. Activate your ET35 remote by touching the screen
2. Press and hold the Setup key until the LED remains on (this occurs after approximately
2-3 seconds) and display shows the Main Setup Screen.
3. Release Setup key.
4. Press and release the Touchscreen "CODE" Key.
5. Display will show the Mode Setup Screen. Press and release Marmitek X-10 Home
Control key .
20055_20061108_UG_EasyTouch_35_touchscreen_remote 09-11-2006 10:22 Pagina 18
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek easytouch 35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek easytouch 35 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info