691528

Makita M1901 Manual

8
Zoom out
Zoom in
Previous page
1/56
Next page
8 ENGLISH
For the correct planer blade setting
Yourplaningsurfacewillenduproughanduneven,unlesstheplanerbladeissetproperlyandsecurely.Theplaner
blademustbemountedsothatthecuttingedgeisabsolutelylevel,thatis,paralleltothesurfaceoftherearbase.
Refertosomeexamplesbelowforproperandimpropersettings.
(A)
(B)
(B)
(A)
(B)
(A)
(A) Front base (Movable shoe)
(B) Rear base (Stationary shoe)
Correct setting
Nicks in surface
Gouging at start
Gouging at end
Although this side view cannot
show it, the edges of the blades
run perfectly parallel to the rear
base surface.
Cause: One or both blades fails to
have edge parallel to rear
base line.
Cause: One or both blade edges
fails to protrude enough in
relation to rear base line.
Cause: One or both blade edges
protrudes too far in relation
to rear base line.
Connecting a vacuum cleaner
For European countries only
►Fig.10
When you wish to perform clean planing operation,
connect a Makita vacuum cleaner to your tool. Then
connect a hose of the vacuum cleaner to the nozzle as
showninthegures.
OPERATION
Holdthetoolrmlywithonehandontheknobandthe
other hand on the switch handle when performing the
tool.
Planing operation
►Fig.11: 1. Start 2. End
Applythetoolfrontbaseatupontheworkpiece
surfacewithouttheplanerbladescontactingthework-
piece.Switchonandwaituntilthebladesattainfull
speed. Then move the tool gently forward at a uniform
speed. Apply pressure on the front of tool at the start of
planing, and on the rear at the end of planing.
Thespeedanddepthofcutdeterminethenish.To
obtainagoodsurfacenish,planedeeplyuntilyouget
near the desired depth, and then plane thinly and slowly
forthenalpass.
Shiplapping (Rabbeting)
►Fig.12
Tomakeasteppedcutasshowninthegure,usethe
edge fence (guide rule).
Draw a cutting line on the workpiece. Insert the edge
fence into the hole in the front of the tool. Align the
bladeedgewiththecuttingline.
►Fig.13: 1. Blade edge 2.Cuttingline
Adjusttheedgefenceuntilitcomesincontactwiththeside
oftheworkpiece,thensecureitbytighteningthescrew.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita M1901 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita M1901 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 7,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info