691824
26
Zoom out
Zoom in
Previous page
1/192
Next page
26 ENGLISH
Table (B)
Molding
position in
the gure
Molding
edge against
guide fence
Finished
piece
For inside
corner
(a) Ceiling
contact edge
should be
against guide
fence.
Finished
piece will be
on the Left
side of blade.
(b) Wall contact
edge should
be against
guide fence.
For outside
corner
(c) Finished
piece will be
on the Right
side of blade.(d) Ceiling
contact edge
should be
against guide
fence.
Example:
In the case of cutting 52/38° type crown molding for
position(a)intheabovegure:
• Tiltandsecurebevelanglesettingto33.9°LEFT.
• Adjustandsecuremiteranglesettingto31.6°
RIGHT.
• Laycrownmoldingwithitsbroadback(hidden)
surface down on the turn base with its CEILING
CONTACTEDGEagainsttheguidefenceonthe
saw.
• Thenishedpiecetobeusedwillalwaysbeon
the LEFT side of the blade after the cut has been
made.
In the case of right bevel cut
(a) (b) (c) (d)
12
1. Inside corner 2. Outside corner
Table (A)
Molding
position
in the
gure
Bevel angle Miter angle
52/38°
type
45° type 52/38°
type
45° type
For
inside
corner
(a) Right
33.9°
Right
30°
Right
31.6°
Right
35.3°
(b) Left
31.6°
Left
35.3°
For
outside
corner
(c)
(d) Right
31.6°
Right
35.3°
Table (B)
Molding
position in
the gure
Molding
edge against
guide fence
Finished
piece
For inside
corner
(a) Wall contact
edge should
be against
guide fence.
Finished
piece will be
on the Right
side of blade.
(b) Ceiling
contact edge
should be
against guide
fence.
For outside
corner
(c) Finished
piece will be
on the Left
side of blade.
(d) Wall contact
edge should
be against
guide fence.
Example:
In the case of cutting 52/38° type crown molding for
position(a)intheabovegure:
• Tiltandsecurebevelanglesettingto33.9°RIGHT.
• Adjustandsecuremiteranglesettingto31.6°
RIGHT.
• Laycrownmoldingwithitsbroadback(hidden)
surfacedownontheturnbasewithitsWALL
CONTACTEDGEagainsttheguidefenceonthe
saw.
• Thenishedpiecetobeusedwillalwaysbeon
the RIGHT side of the blade after the cut has been
made.
Crown molding stopper
Optional accessory
Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
turnbaseasshowninthegures.
At right 45° miter angle
►Fig.49: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
At left 45° miter angle
►Fig.50: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
PositioncrownmoldingwithitsWALLCONTACTEDGE
againsttheguidefenceanditsCEILINGCONTACT
EDGE against the crown molding stoppers as shown in
thegure.Adjustthecrownmoldingstoppersaccording
to the size of the crown molding. Tighten the screws to
secure the crown molding stoppers. Refer to the table
(C) for the miter angle.
►Fig.51: 1. Guide fence 2. Crown molding stopper
26


Need help? Post your question in this forum.

Forumrules
1

Forum

makita-ls1219l

Reset search

  • My saw will not auto lock and the bevel latch will not move help please Submitted on 30-12-2022 at 17:13

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita LS1219L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1219L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info