Manual Makita LS1219L (page 28 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691824

Zoom out

Zoom in

1/192

28 ENGLISH

Special Max Width Cutting

Capacities Technique

The maximum width cutting capacity of this tool can be

achieved by following the steps below:

For the maximum cutting width of this tool refer to the

SPECIFICATIONSunder"Cuttingcapacitiesforspecial

cuttings".

1. Set the tool at 0° or 45° miter angle and make sure

that the turn base is locked. (Refer to the section titled

"Adjustingthemiterangle".)

2. Remove both right and left upper fences temporar-

ily and set aside.

3. Cut a platform to the dimensions indicated in the

gureusinga38mmthick,atstockmaterialsuchas

wood, plywood or particle board.

►Fig.55: 1. 0° Miter angle: Over 450 mm 2. 45° Miter

angle: Over 325 mm 3. 38 mm 4. Over

760 mm

WARNING: Be sure to use at stock as a

platform.Stockthatisnotatmaymoveduringthe

cutting operation which may result in kickback and

seriouspersonalinjury.

NOTE: The maximum cutting capacity in height will

be reduced by the same amount as the platform

thickness.

4. Place the platform on the tool so that it extends

equally over each side of the tool base.

Secure the platform to the tool using four 6 mm wood

screws through four holes in the lower fences.

►Fig.56: 1. Screws (two each side) 2. Lower fence

3. Base 4. Platform

WARNING: Make sure that the platform is lay-

ing at against the tool base and secured rmly

to the lower fences using the four screw holes

provided. Failure to properly secure the platform may

result in movement and possible kickback resulting in

seriouspersonalinjury.

WARNING: Ensure that the tool is rmly

mounted to a stable and at surface. Failure to

properly mount and secure the tool could cause the

tool to be unstable resulting in a loss of control and/

or the tool falling which may result in serious personal

injury.

5. Install the upper fences on the tool.

WARNING: Do not use the tool without upper

fences installed. The upper fences provide the ade-

quate support required to cut the workpiece.

If the workpiece is not supported properly, it may

move resulting in possible loss of control, kickback

andseriouspersonalinjury.

6. Place the workpiece to be cut on the platform

secured to the tool.

7. Securetheworkpiecermlyagainsttheupper

fences with a vise before cutting.

►Fig.57: 1. Upper fence 2. Vertical vise 3. Workpiece

4. Platform

8. Make a cut through the workpiece slowly accord-

ing to the operation titled "Slide (push) cutting (cutting

wide workpieces)."

WARNING: Ensure that the workpiece is

secured with the vise and make the cut slowly.

Failure to do so may cause the workpiece to move

resulting in possible kickback and serious personal

injury.

WARNING: Be aware that the platform may

become weakened after several cuts are per-

formed at various miter angles. If the platform

becomes weakened due to the multiple kerf cuts left

in the material, the platform should be replaced. If the

weakened platform is not replaced, it may cause the

workpiece to move, during cutting, resulting in possi-

blekickbackandseriouspersonalinjury.

Carrying tool

Before carrying, make sure to unplug and all movable

partsofthemitersawaresecured.Alwayscheckthe

following:

• Thetoolisunplugged.

• Thecarriageisat0°bevelanglepositionand

secured.

• Thecarriageisloweredandlocked.

• Thecarriageisfullyslidtotheguidefenceand

locked.

• Theturnbaseisatthefullrightmiterangleposi-

tion and secured.

• Theholdersarestoredandsecured.

Carry the tool by holding both sides of the tool base as

showninthegure.

►Fig.58

WARNING: Stopper pin for carriage elevation

is for carrying and storage purposes only and not

for any cutting operations. The use of the stopper

pin for cutting operations may cause unexpected

movement of the saw blade resulting in kickback and

seriouspersonalinjury.

CAUTION: Always secure all moving portions

before carrying the tool. If portions of the tool move

or slide while being carried, loss of control or balance

mayoccurandresultinpersonalinjury.

MAINTENANCE

WARNING: Always be sure that the tool is

switched off and unplugged before attempting

to perform inspection or maintenance. Failure to

unplug and switch off the tool may result in accidental

start up of the tool which may result in serious per-

sonalinjury.

WARNING: Always be sure that the blade is

sharp and clean for the best and safest perfor-

mance.Attemptingacutwithadulland/ordirtyblade

may cause kickback and result in a serious personal

injury.

My saw will not auto lock and the bevel latch will not move help please Submitted on 30-12-2022 at 17:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1219L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS1219L Manual

Product: