691824

Makita LS1219L Manual

25
Zoom out
Zoom in
Previous page
1/192
Next page
25 ENGLISH
8. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle Bevel angle
Left and Right 0° - 45° Left and Right 0° - 45°
When performing compound cutting, refer to "Press cut-
ting", "Slide (push) cutting", "Miter cutting" and "Bevel
cut" explanations
Cutting base boards
CAUTION: Make sure to use the horizontal
vise (optional accessory) when cutting the base
board.
CAUTION: When cutting the workpiece of the
thickness 20 mm or thinner, make sure to use a
spacer block to secure the workpiece.
When cutting the base board in 45° miter angle, engage
the stopper lever to prevent the blade case from con-
tacting the base board. This will keep the clearance
between the base board and the blade case when the
carriage is fully pushed forward.
RefertotheSPECIFICATIONSforbaseboardcutting
capacity.
►Fig.46: 1. Stopper lever 2. Spacer block
3. Horizontal vise
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
mitersawwiththemoldingslaidatontheturnbase.
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
►Fig.47: 1. 52/38° type crown molding 2. 45° type
crown molding 3. 45° type cove molding
Therearecrownandcovemoldingjointswhichare
madetot"Inside"90°corners((a)and(b)inthegure)
and"Outside"90°corners((c)and(d)inthegure.)
(a) (b) (c) (d)
12
1. Inside corner 2. Outside corner
2
(a)
(b)
(a)
(b)
(b)
(a)
(b)
(a)
(a)
(b)
(c)
(d)
1
1. Inside corner 2. Outside corner
Measuring
Measurethewallwidth,andadjustthewidthofthe
workpieceaccordingtoit.Alwaysmakesurethatwidth
of the workpiece's wall contact edge is the same as wall
length.
►Fig.48: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
Alwaysuseseveralpiecesfortestcutstocheckthe
saw angles.
When cutting crown and cove moldings, set the bevel
angleandmiterangleasindicatedinthetable(A)and
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
(a) (b) (c) (d)
12
1. Inside corner 2. Outside corner
Table (A)
– Molding
position
in the
gure
Bevel angle Miter angle
52/38°
type
45° type 52/38°
type
45° type
For
inside
corner
(a) Left
33.9°
Left 30° Right
31.6°
Right
35.3°
(b) Left
31.6°
Left
35.3°
For
outside
corner
(c)
(d) Right
31.6°
Right
35.3°
… 25 …


Need help? Post your question in this forum.

Forumrules
1

Forum

makita-ls1219l

Reset search

  • My saw will not auto lock and the bevel latch will not move help please Submitted on 30-12-2022 at 17:13

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita LS1219L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1219L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info