Manual Makita LS1219L (page 23 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691824

Zoom out

Zoom in

1/192

23 ENGLISH

NOTICE:Thelowerfencesarexedtothebasein

the factory. Do not remove the lower fences.

NOTICE: If the upper fence is still loose after tight-

eningtheclampingscrew,turntheadjustingscrewto

closeagap.Theadjustingscrewisfactoryadjusted.

You don't need to use it unless needed.

You can store the upper fences onto the holder when

not in use. Use the clip on the upper fence to hold it on

the holder.

►Fig.39: 1. Holder 2. Upper fence 3. Clip

Vertical vise

WARNING: The workpiece must be secured

rmly against the turn base and guide fence with

the vise during all operations. If the workpiece is

not properly secured against the fence the material

may move during the cutting operation causing

possible damage to the blade, causing the material

to be thrown and loss of control resulting in serious

personalinjury.

►Fig.40: 1. Vise arm 2. Vise rod 3. Clamping screw

4. Vise knob

The vertical vise can be installed in two positions on

either the left or right side of the base. Insert the vise

rod into the hole in the base.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the clamping screw contacts

the carriage, install it on the opposite side of vise arm.

Make sure that no part of the tool contacts the vise

when lowering the handle all the way. If some part

contacts the vise, re-position the vise.

Presstheworkpieceatagainsttheguidefenceandthe

turn base. Position the workpiece at the desired cutting

positionandsecureitrmlybytighteningtheviseknob.

NOTE: For a quick setting of workpiece, turning the

vise knob to 90° counterclockwise allows the vise

knob to be moved up and down. To secure the work-

piece after setting, turn the vise knob clockwise.

Horizontal vise

Optional accessory

WARNING: Always rotate the vise nut clock-

wise until the workpiece is properly secured. If

the workpiece is not properly secured the material

may move during the cutting operation causing

possible damage to the blade, causing the material

to be thrown and loss of control resulting in serious

personalinjury.

WARNING: When cutting a thin workpiece,

such as base boards, against the fence, always

use the horizontal vise.

CAUTION: When cutting the workpiece of the

thickness 20 mm or thinner, make sure to use a

spacer block to secure the workpiece.

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

22.5° or greater miter cuts, install the horizontal vise on

the side opposite the direction in which the turn base is

to be turned.

►Fig.41: 1. Vise plate 2. Vise nut 3. Vise knob

Byippingthevisenutcounterclockwise,theviseis

released, and rapidly moves in and out. To grip the

workpiece, push the vise knob forward until the vise

platecontactstheworkpieceandipthevisenutclock-

wise. Then turn the vise knob clockwise to secure the

workpiece.

NOTE: The maximum width of workpiece which can

be secured by the horizontal vise is 228 mm.

Holders

WARNING: Always support a long workpiece

so it is level with the top surface of the turn base

for an accurate cut and to prevent dangerous loss

of tool control. Proper workpiece support will help

avoid blade pinch and possible kickback which may

resultinseriouspersonalinjury.

To hold long workpieces horizontally, holders are pro-

vided on both sides of the tool. Loosen the screws and

extend the holders to the appropriate length for holding

the workpiece. Then tighten the screws.

►Fig.42: 1. Holder 2. Screw

OPERATION

WARNING: Make sure the blade is not con-

tacting the workpiece, etc. before the switch

is turned on. Turning the tool on with the blade in

contact with the workpiece may result in kickback and

seriouspersonalinjury.

WARNING: After a cutting operation, do not

raise the blade until it has come to a complete

stop. The raising of a coasting blade may result in

seriouspersonalinjuryanddamagetotheworkpiece.

WARNING: Do not perform any adjustment

such as turning grip, knob, and levers on the tool

while the blade is rotating. Adjustmentwhilethe

bladeisrotatingmayresultinseriouspersonalinjury.

My saw will not auto lock and the bevel latch will not move help please Submitted on 30-12-2022 at 17:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1219L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS1219L Manual

Product: