Manual Makita LS 1017L (page 12 of 120) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448594

Zoom out

Zoom in

1/120

Symbols END223-1

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

............. Read instruction manual.

............. DOUBLE INSULATION

......... To avoid injury from flying debris, keep

holding the saw head down, after making

cuts, until the blade has come to a

complete stop.

When performing slide cut, first pull

carriage fully and press down handle,

then push carriage toward the guide

fence.

............. Do not place hand or fingers close to the

blade.

.......... Adjust sliding fences clear of blade and

blade guard properly.

...... Never look into the laser beam. Direct

laser beam may injure your eyes.

Intended use

ENE006-1

The tool is intended for accurate straight and miter cutting

in wood. With appropriate saw blades, aluminum can also

be sawed.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB034-6

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before each

use. Do not operate saw if blade guard does not

move freely and close instantly. Never clamp or tie

the blade guard into the open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6. Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

8. Always secure all moving portions before carrying

the tool.

9. Stopper pin which locks the cutter head down is

for carrying and storage purposes only and not for

any cutting operations.

10. Do not use the tool in the presence of flammable

liquids or gases. The electrical operation of the tool

could create an explosion and fire when exposed to

flammable liquids or gases.

11. Check the blade carefully for cracks or damage

before operation.

Replace cracked or damaged blade immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Damage

to these parts could result in blade breakage.

14. Make sure that the turn base is properly secured

so it will not move during operation.

15. For your safety, remove the chips, small pieces,

etc. from the table top before operation.

16. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

17. Make sure the shaft lock is released before the

switch is turned on.

18. Be sure that the blade does not contact the turn

base in the lowest position.

19. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

20. Make sure the blade is not contacting the

workpiece before the switch is turned on.

21. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

22. Wait until the blade attains full speed before

cutting.

23. Stop operation immediately if you notice anything

abnormal.

24. Do not attempt to lock the trigger in the on

position.

25. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a

false sense of security. Blades are extremely

unforgiving.

26. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

27. Do not use the saw to cut other than wood,

aluminum or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS 1017L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS 1017L Manual

Product: