690919

Makita DUR187L Manual

15
Zoom out
Zoom in
Previous page
1/112
Next page
15 ENGLISH
►Fig.12: 1. Most effective cutting area
The nylon cutting head is a dual string trimmer head
provided with a bump & feed mechanism.
To feed out the nylon cord, tap the cutting head against
the ground while rotating.
NOTE: If the nylon cord does not feed out while
tapping the head, rewind/replace the nylon cord
by following the procedures described under
“Maintenance”.
ASSEMBLY
WARNING: Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
inseriouspersonalinjuryfromaccidentalstart-up.
WARNING: Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonalinjuryfromaccidentalstart-up.
Installing the handle
For DUR187U and DUR188U only
1. Insert the shaft of the handle into the grip. Align
the screw hole in the grip with the one in the shaft.
Tighten the screw securely.
►Fig.13: 1. Grip 2.Screw3. Handle
2. Place handle between handle clamp and handle
holder.Adjustthehandletoananglethatprovidesa
comfortableworkingpositionandthensecurewithhex
socket head bolts.
►Fig.14: 1.Hexsocketheadbolt2. Handle clamp
Mounting the attachment pipe
For DUR188U and DUR188L only
Mount the attachment pipe to the power unit.
1. Turn the lever to the direction of the arrow shown
inthegure.
►Fig.15: 1. Lever
2. Pullupthejointcoverandinserttheattachment
pipe while aligning the protrusion on the pipe (cutting
toolside)withtheconcaveportionofthejointpart.
►Fig.16: 1. Lock lever 2. Joint cover 3. Pipe
Make sure that the surface of the lock lever is parallel
to the pipe.
3. Turn the lever to the direction of the arrow shown
inthegure.
►Fig.17: 1. Lever
To remove the pipe, turn the lever to the direction of the
arrowshowninthegureandpullthepipeoutwhile
pressing down the lock lever.
►Fig.18: 1. Lever 2. Lock lever 3. Pipe
Installing the guard
WARNING: Never use the tool without the
guard illustrated in place. Failure to do so can
causeseriouspersonalinjury.
CAUTION: Take care not to injure yourself on
the cutter for cutting the nylon cord.
NOTE: The shape of the protector varies depending
on the country.
1. Aligntheprojectionsontheprotectorwiththe
grooves of the motor housing.
►Fig.19: 1. Protector 2. Groove 3.Projection
2. Aligntheprojectionsontheprotectorholderwith
its counter parts of the motor housing.
►Fig.20: 1. Protector holder 2.Projection
3. Tightenthehexsocketheadboltssecurelyto
fasten the protector and the protector holder.
►Fig.21: 1.Hexsocketheadbolt2.Hexwrench
Installing the wire guard
CAUTION: Before adjusting the wire guard,
wait for the cutting head comes to standstill. Do
not adjust the wire guard with your foot.
►Fig.22
Toreducetheriskdamagingtheobjectsinfrontofthe
cutting head, insert the wire guard so that it controls the
cutting range of the mowing line.
Slightlyexpandthewireguardoutwardandtheninsert
it into the holes of the protector.
►Fig.23: 1.Wireguard
NOTE:Donotexpandthewireguardoutwardtoo
much. Otherwise it may break.
Whenwireguardisnotinuse,liftitfortheidleposition.
►Fig.24
Installing nylon cutting head
Optional accessory
CAUTION: If the nylon cutting head acciden-
tally impacts a rock or hard object during oper-
ation, stop the tool and inspect for any damage.
If the nylon cutting head is damaged, replace it
immediately. Use of a damaged cutting tool could
resultinseriouspersonalinjury.
CAUTION: Make sure to remove the hex
wrench after installation.
NOTICE: Be sure to use genuine Makita nylon
cutting head.
►Fig.25: 1. Nylon cutting head 2. Metal guard
3.Spindle4.Hexwrench
1. Turn the tool upside down so that you can replace
the cutting tool easily.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DUR187L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUR187L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 21,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info