Manual Makita DTR180 (page 17 of 108) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691779

Zoom out

Zoom in

1/108

17 ENGLISH

3. Push the release lever, and lock it with the lock

lever.

►Fig.34: 1. Release lever 2. Lock lever

4. Remove the wire reel from the tool.

NOTE: When wire has been used up normally,

approximately 20 cm of the wire remains wound on

the reel. In this state, replace the wire reel with a new

one.

Ifitisdifculttoremovethewirereelfromthetool,

follow the steps below.

1. Insert the battery cartridge into the tool, and

turn the power on. The tool feeds the wire and cuts it

automatically.

2. Lock the trigger, turn the power off, and remove

the battery cartridge.

3. Remove the wire breaks using tools such as nip-

pers or pliers.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Storage of the hex wrench

Storethehexwrenchinthepositionshowninthegure.

►Fig.35: 1. Hex wrench

Cleaning the cutter

When the tool is used for a long period of time, dust and

wire particles may become adhered to the cutter sec-

tion. In such a case, disassemble and clean the cutter

according to the following procedure.

If a wire is caught in the cutter section, the wire can be

removed by following the same procedure.

Disassembling and cleaning

1. Loosen bolts A and B using the hex wrench

included in the tool package.

►Fig.36: 1. Bolt A 2. Bolt B 3. Contact plate cover

4. Wire guide B

NOTICE: Do not forcibly remove any bolts that

cannot be removed using the hex wrench.

2. Pull the contact plate cover up in the direction of

the arrow and remove it. Bolt B will be removed at the

same time.

►Fig.37: 1. Contact plate cover 2. Bolt B

3. Remove bolt A, and remove wire guide B.

►Fig.38: 1. Bolt A 2. Wire guide B

4. Turn wire guide B over and clean its inside.

►Fig.39

5. Remove cutter A, cutter B, top plate, and link arm

A from arm plate A. Then, clean them.

►Fig.40: 1. Cutter B 2. Link arm A 3. Cutter A 4. Arm

plate A 5. Top plate

Assembling

Whencleaningisnished,assemblethepartsaccord-

ing to the following procedure.

1. InstallcutterAandlinkarmAtottheshapeof

arm plate A.

►Fig.41: 1. Cutter A 2. Link arm A 3. Arm plate A

2. Install cutter B and the top plate onto arm plate A.

(Install cutter B on cutter A and link arm A.)

►Fig.42: 1. Cutter B 2. Top plate 3. Arm plate A

4. Cutter A 5. Link arm A

NOTICE: Face the projection of cutter B down-

ward, and install the cutter as shown in the gure.

3. Align the pipe of the tool with the groove inside the

wire guide B, and assemble them.

►Fig.43: 1. Pipe 2. Groove 3. Wire guide B

4. Fix wire guide B by temporarily tightening bolt A.

►Fig.44: 1. Bolt A 2. Wire guide B

5. Install the contact plate cover in the direction of

the arrow.

►Fig.45: 1. Contact plate cover

6. Fix wire guide B and contact plate cover securely

by tightening bolt A and bolt B.

►Fig.46: 1. Wire guide B 2. Contact plate cover

3. Bolt A 4. Bolt B

7. Afterassembling,conrmthatthecontactplate

canmoveasshowninthegure.

►Fig.47: 1. Contact plate

NOTE: If the contact plate is caught, press it as

showninthegure.

►Fig.48

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTR180 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 23,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DTR180 Manual

Product: