691779

Makita DTR180 Manual

16
Zoom out
Zoom in
Previous page
1/108
Next page
16 ENGLISH
Tying work
CAUTION: Before inserting the battery car-
tridge, be sure to release your ngers from the
switch trigger and lock the trigger. If you insert
the battery cartridge while the switch trigger is being
pulled, it may cause an accident if the wire tying
process is accidentally carried out.
CAUTION: When you turn the power on, never
bring your limbs or face close to the binding or
rotating parts of the tool tip. Otherwise, you may
beinjured.
CAUTION: When the power is turned on,
never touch the binding or rotating parts of the
tool tip.Otherwise,youmaybeinjured.
►Fig.23
Preparation before work
1. Make sure that the battery cartridge is removed
and the trigger is locked.
2. Insert the battery cartridge into the tool, and turn
the power on. When you turn the power on, the wire is
cut automatically.
NOTICE: Make sure that the tying mode lamp
lights up when the power is turned on. If it does
not light up, recharge the battery.
3. Release the trigger lock.
►Fig.24: 1. Trigger-lock button 2. Switch trigger
3. Power button 4. Tying mode lamp
Single actuation mode
1. Push the arm securely against the tying point.
Push the tool vertically against the rebars, and press
the arm against the point where the rebars cross at a
45-degree angle.
►Fig.25
2. Pull the switch trigger once.
3. The wire is fed and cut automatically.
4. The hook holds and twists the wire, then returns to
the original position after the wires have been tied.
►Fig.26
5. After tying, exercise care not to hook the arm on
the rebars and pull the tool up.
CAUTION: If the wire has clung to the binding
part of the tool tip, turn the power of the tool off.
Lock the trigger, remove the battery cartridge,
and remove the wire using tools such as nippers
or pliers.
►Fig.27
Continuous actuation mode
1. Switch the tool mode from the single actuation
mode to the continuous actuation mode using the mode
switching button.
►Fig.28: 1. Mode switching button
2. Release the trigger lock.
3. While pulling the switch trigger, push the tool
vertically against the rebars, and press the arm against
the point where the rebars cross at a 45-degree angle.
Pressthecontactplatermlyagainstthetyingpoint.
The wire will be tied.
►Fig.29: 1. Contact plate
4. After tying, exercise care not to hook the arm on
the rebars and pull the tool up.
►Fig.30
Cautions on working
• If you move the arm from the tying position during
the wire tying process, the wire will get stuck on
the hook, which may lead to incorrect tying.
• Keep pressing the tool against the rebars until the
wire tying process is completed.
• Do not move to the next tying point until the cur-
rent wire tying process is completed.
• The tool tip rotating part (hook) twists the wire
duringthewiretyingprocess.Holdthegriprmly
so that your body is not pulled by the tool.
• Do not touch the wires during the wire tying
process.
• If you are repeating the wire tying processes in
thesingleactuationmode,fullyreleaseyournger
from the switch trigger. Then, continue to operate
the switch trigger.
• If you pull the switch trigger when there is no tie
wire left, an error is displayed. Replace with a new
tie wire and restart the tool.
Tying tips
• Tilt the tool at a 45° angle to the crossed rebars,
andtiealternatelyasshowninthegure.
►Fig.31
• Avoid strumous sections of rebars.
►Fig.32
• Iftyingstrengthisinsufcient,changethetying
orientation and perform tying twice so that tying
strength increases.
►Fig.33
NOTICE: When you make the second tie, bend
the tail of the rst tie before making the second
tie. Otherwise, the wire may be repelled a second
time. It may cling to the tool tip, and the hook may be
damaged.
Replacing the tie wires
CAUTION: When you replace the wire, be sure
to turn the power off, lock the trigger, and remove
the battery cartridge. Failure to do so may cause an
accident.
1. When wire has been used up, an error tone will
sound and error "1" will be displayed.
2. Lock the trigger, turn the power off, and remove
the battery cartridge.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DTR180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTR180 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 23,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info