691782

Makita DLS111 Manual

34
Zoom out
Zoom in
Previous page
1/244
Next page
34 ENGLISH
State of abnormality Probable cause (malfunction) Remedy
Thevacuumcleanerdoesnotrun
along with the switch operation of
the tool.
Thewirelessunitisnotinstalledinto
the tool.
Thewirelessunitisimproperlyinstalled
into the tool.
Install the wireless unit correctly.
Theterminalofthewirelessunitand/or
the slot is dirty.
Gently wipe off dust and dirt on the terminal of the
wireless unit and clean the slot.
Thewirelessactivationbuttononthe
tool has not been pushed.
Pushthewirelessactivationbuttonbrieyandmake
sure that the wireless activation lamp is blinking
in blue.
Thestand-byswitchonthevacuum
cleanerisnotsetto"AUTO".
Set the stand-by switch on the vacuum cleaner to
"AUTO".
More than 10 tools are registered to the
vacuum cleaner.
Perform the tool registration again.
If more than 10 tools are registered to the vacuum
cleaner, the tool registered earliest will be cancelled
automatically.
Thevacuumcleanererasedalltool
registrations.
Perform the tool registration again.
No power supply Supply the power to the tool and the vacuum
cleaner.
Thetoolandvacuumcleanerisaway
from each other (out of the transmission
range).
Get the tool and vacuum cleaner closer each other.
Themaximumtransmissiondistanceisapproxi-
mately 10 m however it may vary according to the
circumstances.
Radio disturbance by other appliances
which generate high-intensity radio
waves.
Keep the tool and vacuum cleaner away from the
appliances such as Wi-Fi devices and microwave
ovens.
Thevacuumcleanerrunswhilethe
tool's switch trigger is not pulled.
Other users are using the wireless
activation of the vacuum cleaner with
their tools.
Turnoffthewirelessactivationbuttonoftheother
tools or cancel the tool registration of the other
tools.
MAINTENANCE
WARNING: Always be sure that the tool is
switched off and batteries are removed before
attempting to perform inspection or maintenance.
Failure to removing the batteries and switch off the
tool may result in accidental start up of the tool which
mayresultinseriouspersonalinjury.
WARNING: Always be sure that the blade is
sharp and clean for the best and safest perfor-
mance.Attemptingacutwithadulland/ordirtyblade
may cause kickback and result in a serious personal
injury.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Adjusting the cutting angle
Thistooliscarefullyadjustedandalignedatthefactory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
Lower the handle fully and lock it in the lowered position
by the stopper pin. Push the carriage toward the guide
fence. Loosen the grip and the screws which secure the
pointer and miter angle scale.
►Fig.70: 1. Screw on pointer 2. Screws on miter
angle scale 3. Miter scale
Set the turn base to the 0° position using the positive
stopfunction.Squarethesideofthebladewiththeface
oftheguidefenceusingatriangularruleortry-square.
Whilekeepingthesquare,tightenthescrewsonthe
miteranglescale.Afterthat,alignthepointers(both
right and left) with the 0° position in the miter angle
scale and then tighten the screw on the pointer.
►Fig.71: 1.Triangularrule
Bevel angle
0° bevel angle
Push the carriage toward the guide fence and lock the
sliding movement by the stopper pin. Lower the handle
fully and lock it in the lowered position by the stopper
pinandthenloosentheknob.Turnthe0°adjusting
bolt two or three revolutions counterclockwise to tilt the
blade to the right.
►Fig.72: 1.0°Adjustingbolt2. Screw
Carefullysquarethesideofthebladewiththetop
surface of the turn base using the triangular rule, try-
square,etc.byturningthe0°adjustingboltclockwise.
Thentightentheknobrmlytosecurethe0°angleyou
have set.
►Fig.73: 1.Triangularrule2. Saw blade 3.Topsur-
face of turn base
Checkifthesideofthebladesquareswiththeturnbase
surface once again. Loosen the screw on the pointer.
Alignthepointerwith0°positioninthebevelangle
scale and then tighten the screw.
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DLS111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS111 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 37,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info