691782

Makita DLS111 Manual

35
Zoom out
Zoom in
Previous page
1/244
Next page
35 ENGLISH
45° bevel angle
NOTICE: Before adjusting the 45° bevel angle,
nish 0° bevel angle adjustment.
Loosen the knob and fully tilt the carriage to the side
that you want to check. Check if the pointer indicates
the 45° position in the bevel angle scale.
►Fig.74
If the pointer does not indicate the 45° position, align
itwith45°positionbyturningtheadjustingboltonthe
opposite side of the bevel angle scale.
►Fig.75: 1.Left45°adjustingbolt2.Right45°adjust-
ing bolt
Adjusting the laser line position
For DLS111, DLS112 only
WARNING:
The batteries must be installed
while adjusting the laser line. Take extra care not
to switch on the tool during adjustment.Accidental
startupofthetoolmayresultinseriouspersonalinjury.
CAUTION: Never look directly into the laser
beam. Direct eye exposure to the beam could cause
serious damage to your eyes.
NOTICE: Check the position of laser line regu-
larly for accuracy.
NOTICE: Beware that impacts to the tool. It may
cause the laser line to be misaligned or may cause
damage to the laser, shortening its life.
NOTICE: Have the tool repaired by a Makita
authorized service center for any failure on the
laser unit.
Themovablerangeoflaserlineisdecidedbytherange
adjustmentscrewsonbothsides.Performfollowing
procedures to alter the laser line position.
1. Remove the batteries.
2. Draw a cutting line on the workpiece and place it
ontheturnbase.Atthistime,donotsecurethework-
piece with a vise or similar securing device.
3. Lower the handle and align the cutting line with
the saw blade.
4.
Return the handle to the original position and secure
the workpiece with the vertical vise so that the workpiece
does not move from the position you have determined.
5. Install the batteries and turn on the laser switch.
6. Loosentheadjustingscrew.Tomovethelaserline
awayfromtheblade,turntherangeadjustmentscrews
counterclockwise.Tomovethelaserlineclosetothe
blade,turntherangeadjustmentscrewclockwise.
Adjusting the laser line on the left side of the blade
►Fig.76:
1.Adjustingscrew2.Rangeadjustmentscrew
3. Hex wrench 4. Laser line 5. Saw blade
Adjusting the laser line on the right side of the blade
►Fig.77:
1.Adjustingscrew2.Rangeadjustmentscrew
3. Hex wrench 4. Laser line 5. Saw blade
7. Slidetheadjustingscrewtothepositionthatthe
laser line comes onto the cutting line and then tighten.
NOTE:
Themovablerangeoflaserlineisfactoryadjusted
within1mm(0.04")fromthesidesurfaceofblade.
Cleaning the laser light lens
For DLS111, DLS112 only
Thelaserlightbecomeshardtoseeasthelensforthelaser
light gets dirty. Clean the lens for laser light periodically.
►Fig.78: 1. Screw 2. Lens
Remove the batteries. Loosen the screw and pull out
the lens. Clean the lens gently with a damp soft cloth.
NOTICE: Do not remove the screw which
secures the lens. If the lens does not come out,
loosen the screw further.
NOTICE: Do not use solvents or any petro-
leum-based cleaners on the lens.
After use
Afteruse,wipeoffchipsanddustadheringtothetool
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered
sectiontitled"Bladeguard".Lubricatetheslidingpor-
tions with machine oil to prevent rust.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
WARNING: These Makita accessories or
attachments are recommended for use with your
Makita tool specied in this manual.Theuseof
any other accessories or attachments may result in
seriouspersonalinjury.
WARNING: Only use the Makita accessory
or attachment for its stated purpose. Misuse of
an accessory or attachment may result in serious
personalinjury.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Steel&Carbide-tippedsawblades
• Verticalvise
• Horizontalvise
• Crownmoldingstopperset
• Dustbag
• Triangularrule
• Hexwrench
• Hexwrench(forlaseradjustment)
• Wirelessunit(forDLS111)
• Makitagenuinebatteryandcharger
NOTE: Some items in the list may be included in the
toolpackageasstandardaccessories.Theymay
differ from country to country.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DLS111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS111 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 37,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info