Manual Makita BUK360 (page 10 of 96) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600691

Zoom out

Zoom in

1/96

011713

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Battery converters (optional accessory)

WARNING:

• Before installing or removing the battery converters

BCV01/BCV03, remove the lock key.

BCV01 (optional accessory)

WARNING:

• When using the BCV01, be sure to use the holder

(optional accessory) to retain its cord. Failure to use

the holder leaves the cord loose. This may cause the

cord to be entangled by the blade, resulting in damage

to the tool and a personal serious injury.

• When using the BCV01, never attach it to any part of

your body. Attaching the BCV01 to any part of your

body may cause a serious injury. (Fig. 5)

Hook the battery converter BCV01 onto installation

section of the handle.

Holder (optional accessory)

When using the BCV01, be sure to use the holder

(optional accessory) to retain its cord. (Fig. 6)

Fit the holder (optional accessory) in the hole on the left

side of the handle from the operator’s view. And then

push the cord into the holder so that the cord tension is

not too loose. Make sure the cord is secured with the cord

holder. (Fig. 7)

Open out the battery hood and then slide all the way and

click the product mounting adapter of the BCV01 into the

battery port 1. (Fig. 8)

Pull up lightly and remove the rubber cap from the slit in

the lower housing as shown in the figure.

NOTE:

• Do not pull up the rubber cap forcibly because forcing it

may damage its retaining section. (Fig. 9)

Bend the cord of the battery converter BCV01 over the

product attachment section. Then run the cord of the

BCV01 through the slit in the lower housing and close the

battery hood.

To remove the BCV01, follow the installation procedure in

reverse.

BCV03 (optional accessory) (Fig. 10)

Open the battery hood and click in the BCV03 into the

battery port. Close the battery hood.

To remove the BCV03, press on the hook of the BCV03

and withdraw it with both hands.

Indication lamp

WARNING:

• Do not use the battery selection switch during the

operation.

• After flipping the battery selection switch, the main

switch is turned off. To start the tool, the operator

needs to press the main switch. (Fig. 11 & 12)

You can switch the battery by flipping the battery selection

switch when the tool is equipped two batteries. (The

indication lamps shows the status No. 1 or No. 6.)

If the tool is equipped one battery, flip the battery button to

chose one side which the battery is equipped.

• If the tool is equipped one battery and you switch to a

battery port in which no battery cartridge is mounted,

the indication lamps shows the status No. 2 or No. 5.

The warning lamp lights up when a problem occurs, and

the tool is automatically switched off about 10 seconds

after the warning lamp has lighted. The indication of the

warning lamp means as follows.

• Lighting-up-red: There are two possibility why the red

lamp lights up.

• The motor is overheated. (The indication lamp

shows the status No. 3.)

Turn off the main switch, and restart the tool after

the motor cools down.

• The battery capacity is low. (The indication lamp

shows the status No. 2 or No. 5.)

Turn off the main switch, and recharge the battery

cartridge.

• Blinking red: The blade becomes overloaded by

getting stuck because of digging too deep, or clogged

up by weeds or stone. (The indication lamp display

shows the status No. 4.)

Switch off the tool by pressing the main switch, lift the

blade by holding the handle, and check whether a

obstacle blocks the blade.

CAUTION:

• Always switch off the tool and remove the battery

cartridge before removing the obstacle.

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may

have malfunctioned.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BUK360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BUK360 Manual

Product: