Manual Makita BUK360 (page 11 of 96) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600691

Zoom out

Zoom in

1/96

• Do not forcibly rotate the blade, or hit it with a hammer,

the tool may be damaged.

If there is a obstacle stuck on the blade, remove it

carefully.

Turn on the main switch, and check the red light is off.

Power switch action

WARNING:

• Before inserting the battery cartridge in the tool,

always check to see that the switch lever actuates

properly and returns to the original position when

released. Operating a tool with a switch that does not

actuate properly can lead to loss of control and serious

personal injury.

NOTE:

• The motor does not start if the motor is overloaded. In

that case, change the depth of cultivation much

shallower.

• The tool does not start without pressing the lock-off

button even if the switch lever is pulled.

This tool equips the lock key to prevent children from

accidentally starting up the tool. The lock key locates

under the battery hood. Insert the lock key before you

switch on the tool. The tool does not start up when the

lock key is pulled out. (Fig. 13 & 14)

To switch on the tool, press the main switch. One of the

indication lamp lights up when you switch on the tool. To

switch off the tool, press the main switch again.

To prevent the tool from unintentional starting, a lock-off

button is provided. To start the blades’ rotating, depress

the lock-off button and then pull the switch lever. Release

the switch lever to stop.

Drag bar (Fig. 15)

The drag bar adjust the depth of the cultivation. The drag

bar also prevents sudden uncontrollable move of the tool.

You can change the depth of the cultivation by changing

the position of the drag bar. (Fig. 16)

CAUTION:

• Always be sure that the transport wheel is in the

transporting position before you adjust the drag bar.

1. Remove the stopper which holds the drag bar.

2. Adjust the position of the drag bar, then hold the

position with the stopper.

Positioning guide

• Deep cultivation - A

• Middle depth cultivation - B

• Shallow cultivation - C

• Transport position - D

NOTE:

• If the field is solid and the tool advances too fast, set

the drag bar at the deep cultivation position - A. If the

field is soft and the blade sinks in the field, set the drag

bar at the shallow cultivation position - C.

• When you transport the tool, place the drag bar at

transport position - D.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out

any work on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembled state may result in serious personal injury

from accidental start-up.

Installing the drag bar and stopper

(Fig. 17)

To install the drag bar with stopper, refer to the section

titled “Drag bar” in FUNCTIONAL DESCRIPTION.

Setting the lock key (Fig. 18)

To set the lock key, refer to the section titled “Power

switch action” in FUNCTIONAL DESCRIPTION.

Assembling and adjusting the angle of

the handle

CAUTION:

• Always perform the adjusting on the flat surface to

avoid accidents.

• Always be sure that the transport wheel is in the

transporting position before you adjust the angle of the

handle.

• Always hold the handle while adjusting, or the handle

may fall on person and cause injuries.

• When adjusting the angle of the handle, be careful not

to have your thumb and fingers pinched between the

handle and the frame. (Fig. 19, 20 & 21)

To assemble the handle on the equipment, put the corn

spring over the handle locking knob and firmly screw them

into the handle piercing it through one of the three handle-

retaining-shaft holes. At this time, put the corn spring over

the handle locking knob so that the swollen surface of the

corn spring faces the handle locking knob. Make sure that

the handle is secured after assembling it.

You can adjust the angle of the handle from three angles.

Hold the handle by one hand, and then turn and remove

the handle locking knob. Choose the favorable angle from

one of the three holes, and return the handle locking knob

and tighten it firmly.

CAUTION:

Always be sure that the handle locking knob is tightened

firmly, or the handle may fall on you and cause injuries.

OPERATION

Starting forward

WARNING:

• Make sure that you hold the handle firmly before

starting the tool. When the field is solid, the tool runs

forward suddenly because the blade does not dig

enough into the field, and may cause injuries.

Push down the handle and place the drag bar into the field

to cultivate. Control the handle up and down, and adjust

the depth of the drag bar in accordance with solidity of the

field. You can dig deeper when you push down the handle

more and place the drag bar deeper. The tool moves

faster and lighter when you lift the handle and pull the

drag bar out from the field.

The tool stops when you release the switch lever.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BUK360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BUK360 Manual

Product: