598435
15
Zoom out
Zoom in
Previous page
1/24
Next page
15
Cold start
F
- Prime the fuel pump (G/5) by pressing it several times until
you can see fuel in the pump.
- Actuate the half-throttle lock by depressing the safety lock
(F/3), pressing in the throttle (F/1) and moving the combi-
nation switch (F/2) into the START position. Then release
throttle (F/1) and then the combination switch (F/2).
- Turn the choke lever (G/4) to the CHOKE (closed) posi-
tion.
- Hold the brushcutter with one hand as shown in Fig. E on
page 14.
- Pull the starter cable slowly until you feel resistance (piston
is just before top dead centre).
- Now pull quickly and forcefully until you hear the rst
audible ignition (the engine will start brie y).
- Do not pull out the whole starter cable to its full extent and
do not let the starter handle jump back, but let it slowly
automatically rewind itself.
- Turn the choke lever (G/4) to the RUN (open) position and
pull the starting handle again until the engine runs.
- Once the engine has started, press the throttle (F/1) all the
way and release it again immediately. The half-throttle catch
will come out and the engine will idle.
Warmstart
- If the engine is warmed up do not prime the fuel pump.
- Move the combination switch (F/2) to the “I” position.
- Do not turn the choke switch to the CHOKE (closed) posi-
tion, but to RUN.
Stop engine
Move the combination switch (F/2) to the “O” position.
H
Important: The cutting tool must not rotate when the engine
is idling! If it does, adjust the idle speed.
- The appropriate cutting tool must be mounted.
- Make sure the air lter is clean.
- Let the engine run warm.
- Do not operate the throttle (F/1).
- Unscrew the adjustment screw (H/6) no more than 1/8 turn
(counter-clockwise).
- Repeat the procedure if the cutting tool still rotates during
idling.
If the cutting tool does not stop, do NOT work with the brushcut-
ter. Take it to a MAKITA service centre!
Idle adjustment
G
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BCM3310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCM3310 in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info