598386
6
Zoom out
Zoom in
Previous page
1/240
Next page
6
MOTOR THERMAL OVERLOAD
PROTECTOR:
When the current rating of the motor is exceeded the
thermo-protector will open and shut off the motor
automatically.
The motor must be allowed to cool down before restarting.
The compressor will automatically restart after the motor
has cooled down.
ON/AUTO - OFF SWITCH:
Turn this switch to “on” to provide automatic power to the
pressure switch and to “off” to remove power when
finished using the compressor or when compressor will be
left unattended.
AIR INTAKE FILTER:
This filter is designed to clean air coming into the
compressor pump. This filter must always be clean and
free from obstructions. See “Maintenance”.
AIR COMPRESSOR PUMP:
To compress air, the piston moves up and down in the
cylinder. On the down stroke, air is drawn in through the
air intake valve. The exhaust valve remains closed.
On the upstroke of the piston, air is compressed. The
intake valve closes and compressed air is forced out
through the exhaust valve, through the outlet tube,
through the check valve and into the air tank. Useable air
is not available until the compressor has raised the air
tank pressure above that required at the air outlet.
CHECK VALVE:
When the air compressor is operating, the check valve is
“open”, allowing compressed air to enter the air tank.
When the air compressor reaches “cut-out” pressure, the
check valve “closes”, allowing air pressure to remain
inside the air tank.
PRESSURE SWITCH UNLOADING VALVE:
The pressure switch unloading valve located on the side
of the pressure switch, is designed to automatically
release compressed air from the compressor head and
the outlet tube when the air compressor reaches “cut-out
pressure.
PRESSURE SWITCH:
The pressure switch automatically starts the motor when
the air tank pressure drops to the factory set “cut-in”
pressure. It stops the motor when the air tank pressure
reaches the factory set “cut-out” pressure.
SAFETY VALVE:
If the pressure switch does not shut off the air compressor
at its "cut-out" pressure setting, the safety valve will
protect against high pressure by “popping out” at its
factory set pressure which is slightly higher than the
pressure switch “cut-out” setting.
OUTLET PRESSURE GAUGE:
The outlet pressure gauge indicates the air pressure
available at the outlet side of the regulator. This pressure
is controlled by the regulator and is always less or equal
to the tank pressure. See “Operating Procedures”.
TANK PRESSURE GAUGE:
The tank pressure gauge indicates the air pressure in the
tank.
REGULATOR:
The air pressure coming from the air tank is controlled by
the regulator knob. Turn the knob clockwise to increase
pressure and counter-clockwise to decrease pressure. To
avoid minor re-adjustment after making a change in
pressure setting, always approach the desired pressure
from a lower pressure. When reducing from a higher to a
lower setting, first reduce the pressure less than the
desired pressure. Depending on the air requirements of
each particular accessory, the outlet regulated air
pressure may have to be adjusted while you are operating
the accessory.
COMPRESSED AIR OUTLET; “HP” marking
For High Pressure Pneumatic Tool Exclusive Use
Outlet Max Pressure; 2.6 MPa (26 bar)
COMPRESSED AIR OUTLET; “RP” marking
For Regular Pressure Pneumatic Tool Use
Outlet Max Pressure; 0.9 MPa (9 bar)
INSTALLATION AND BREAK-IN
PROCEDURES
LOCATION OF THE AIR COMPRESSOR
Locate the air compressor in a clean, dry and well-
ventilated area. The air filter must be kept clear of
obstructions, which could reduce air delivery of the air
compressor. The air compressor should be located at
least 0.3 m away from the wall or other obstructions that
would interfere with the flow of air. The air compressor
head and shroud are designed to allow for proper cooling.
If humidity is high, an air filter can be installed on the air
outlet adapter to remove excessive moisture. Follow the
instructions packaged with the air filter for proper
installation.
Place the air compressor on a level surface so that it rests
securely on the rubber feet.
LUBRICATION
This air compressor is equipped with an Oil-Less pump
designed for durability and no maintenance.
Power supply
Operate the compressor at voltages specified on the
nameplate, the allowable tolerance range must remain
within ±5%. If using the compressor at a higher voltage
than the rated voltage, it will result in abnormally fast
motor speed and may damage the unit and burn out the
motor.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AC310H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AC310H in the language / languages: All languages as an attachment in your email.

The manual is 5,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info