448175
8
Zoom out
Zoom in
Previous page
1/17
Next page
8
1. Removing blades
Loosen the thumb screw which secures the chip
cover and remove the chip cover. Remove the
screws which secure the right side cover. Then
remove the right side cover. Turn the pulley until the
drum can be locked in the position whereby the
blade installation bolts face upward. (Fig. 8)
For throw away blades only
Place the two magnetic holders on the set plate and
push them in the direction of the arrow until the claw
contact the blade. Remove the six blade installation
bolts using the socket wrench. Grip the magnetic
holders and raise them straight up to remove the set
plate and the blade from the drum. Press the lock
plate and turn the pulley 180° to lock the drum.
Remove the other blade as described above. (Fig. 9
& 10)
For standard blades only
Remove the six installation bolts using the socket
wrench. Raise the set plate and blade straight up to
remove them from the drum. Press the lock plate
and rotate the drum by turning the pulley 180° to
lock the drum. Remove the other blade as described
above. Remove the set plate from the blade. (Fig. 11
& 12)
2. Installing blades
CAUTION:
Use only Makita socket wrench provided to tighten
the blade installation bolts. The use of any other
socket wrench may cause overtightening or insuffi-
cient tightening of the bolts, resulting in severe
injury.
For throw away blades only
Provide a flat wood block approximately 300 mm
long and 100 mm wide. Place the blade and the set
plate on the wood block so that the blade locating
lug of the set plate rests in the groove of the blade.
Adjust the set plate so that both ends of the blade
protrude approximately 1 mm beyond the end of the
set plate. Place the two magnetic holders on the set
plate and push them until the claw contacts the
blade. (Fig. 13)
Grip the magnetic holder and slip the heel of the set
plate into the groove in the drum. Install the blade
installation bolts. (Fig. 9)
After tightening all the blade installation bolts lightly
and evenly from the center to the outside, tighten
them completely following the same sequence.
Remove the magnetic holders from the set plate.
Install the other blade as described above. Rotate
the drum slowly while pressing the lock plate to
make sure there is nothing abnormal. Then install
the chip cover and the side cover. (Fig. 10)
CAUTION:
Do not tighten the blade installation bolts without
the blade locating lug of the set plate correctly
resting in the groove of the blade. This may cause
damage to the blade and potential injury to the
operator.
Do not turn the tool on with the chip cover
removed.
When installing the chip cover, make sure that the
chain is not caught by the chip cover.
For standard blades only
Place the blade on the blade gauge so that the blade
edge is perfectly flush with the inside of the front rib
(A). Place the set plate on the blade, then gently
press the heel of the set plate flush with the back
side of the blade gauge (B). Tighten the screws to
secure the set plate to the blade.
Slip the heel of the set plate into the groove in the
drum. Install the blade installation bolts. (Fig. 14)
After tightening all the blade installation bolts lightly
and evenly from the center to the outside, tighten
them completely following the same sequence.
(Fig. 15)
Install the other blade as described as above. Rotate
the drum slowly while pressing the lock plate to
make sure there is nothing abnormal. Then install
the chip cover and the side cover. (Fig. 16)
CAUTION:
Tighten the blade installation bolts securely when
installing the blades.
Do not turn the tool on with the chip cover open.
When installing the chip cover, make sure that the
chain is not caught by the chip cover.
Changing type of blade
This tool can accept either throw away blades or standard blades. If you wish to change the type of blade, buy and use
the following parts.
Hood set (Fig. 17)
When you wish to maintain clean operations through easy dust collection, connect the vacuum cleaner to the thick-
nesser using this hood.
Loosen the thumb screws which secure the chip cover. Attach the hood to the thicknesser and secure the chip cover
and the hood together by tightening the thumb screws.
CAUTION:
When installing the hood set, make sure that the chain is not caught by the chip cover or hood set. (Fig. 18)
Changing from standard blade to throw-away blade Changing from throw-away blade to standard blade
Set plate 2 pcs. Set plate 2 pcs.
Throw-away blade (306 mm) 2 pcs. Pan head screw M 4 x 6 4 pcs.
Magnetic holder 2 pcs. Standard blade 2 pcs.
Blade gauge 1 pc.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 2012 NB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2012 NB in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita 2012 NB

Makita 2012 NB User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info