448175

Makita 2012 NB Manual

9
Zoom out
Zoom in
Previous page
1/17
Next page
9
OPERATION
CAUTION:
• Two or more pieces of narrow but similar thickness stock can be passed through the thicknesser side by side. How-
ever, allow some spacing between the stock to permit the feed rollers to grip the thinnest piece of stock. Otherwise, a
slightly thinner piece could be kicked back by the cutterhead.
Place the workpiece flat on the table top.
Determine the depth of cut as described before.
Switch on the tool and wait until the blades attain full speed. The workpiece should not be in contact with the feed roller
when you turn the tool on.
Then insert the workpiece flush with the table top.
When cutting a long or heavy workpiece, lift up its end slightly at the start and the end of the cut to avoid gouging or
snipping at the extreme ends of the workpiece.
The use of the tool top enables quick, effortless return of the workpiece to the infeed table side. This is especially con-
venient with two operators. (Fig. 19)
CAUTION:
• The workpiece with the following dimensions cannot be fed into the tool because the interval between two feed roll-
ers is 129 mm. Do not try to cut them. (Fig. 20)
• Stop the tool when the workpiece has stalled. Allowing the tool to run with a stalled workpiece causes rapid wearing
of the feed rollers.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Adjusting height of sub-table (Fig. 21 & 22)
The height of sub-table is factory-adjusted. If further
adjustment is necessary, proceed as follows.
Place a postcard on the table and also place a ruler on
the postcard. Turn the adjusting screw with the hex
wrench until the end of the sub-table contacts the ruler.
Now the end of the sub-table is from 0.1 mm to 0.3 mm
above the table surface.
Replacing carbon brushes (Fig. 23 & 24)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
Keeping blades sharp
Dull blades can cause rough finish, an overload of the
motor and dangerous kickback of the workpiece.
Replace dull blades immediately.
Lubrication (Fig. 25)
Oil the chain (after removing the side cover R), the four
columns and the screws for elevating the main frame.
This periodic lubrication should be performed with
machine oil.
CAUTION:
• Oiling and all maintenance should be done with the tool
turned off and unplugged.
Cleaning
Always brush off dirt, chips and foreign matter adhering
to the roller surfaces, motor vents and drums.
Limit for re-sharpening of standard blade (Fig. 26)
Do not use the standard blade whose blade length is
under 4 mm.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
1 Less than 130 mm long
2 Having a groove more than 130 mm wide
3 Having grooves at intervals of 130 mm wide
Less than 130 mm
More than 130 mm
130 mm
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 2012 NB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2012 NB in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita 2012 NB

Makita 2012 NB User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info