448175
6
Zoom out
Zoom in
Previous page
1/17
Next page
6
ENGLISH
Explanation of general view
1 Carrying handle
2Sub-table
3 Bolt or screw
4 Pilot lamp
5 Switch
6 Crank handle
7Scale
8 Main frame
9 Indicator plate
10 Depth gauge
11 Groove
12 Depth adjusting gauge
13 Stopper
14 Stopper button
15 Stopper knob
16 Table top
17 Lock plate
18 Pulley
19 Drum
20 Chain
21 Thumb screw
22 Blade installation bolt
23 Set plate
24 Blade
25 Claw
26 Magnetic holder
27 Socket wrench
28 Blade installation bolt
29 Screw
30 Blade gauge
31 Hood set
32 Chip cover
33 Ruler
34 Post card
35 Adjusting screw
36 Hex wrench
37 Limit mark
38 Brush holder cap
39 Screwdriver
40 Column
41 Base
42 More than 4 mm
SPECIFICATION
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.38 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
ENB065-1
1. Wear eye protection.
2. Wear suitable personal protective equipment
when necessary, such as hearing protection (ear
plugs), respiratory protection (dust mask) and
gloves when handling rough material.
3. Do not use the tool in the presence of flammable
liquids or gases.
4. Make sure that all covers are installed in place
before operation.
5. Handle the blades very carefully.
6. Check the blades carefully for cracks or damage
before operation. Replace cracked or damaged
blades immediately.
7. Tighten the planer blade installation bolts
securely.
8. Remove nails and clean the workpiece before
cutting. Nail, sand or foreign matter can cause
blade damage.
9. Do not remove chips from the chip chute when
the motor is running. Clean out chips after the
blades come to a complete stop. Always use a
stick etc. when cleaning them out.
10. Do not leave the tool running.
11. Do not abuse cord. Never yank cord to discon-
nect it from receptacle. Keep cord away from
heat, oil water and sharp edges.
SAVE THESE INSTRUCTIONS.
Model 2012NB
Cutting width 304 mm
Max. cutting depth
3.0 mm of stock width less than 150 mm
1.5 mm of stock width from 150 mm to 240 mm
1.0 mm of stock width from 240 mm to 304 mm
Feed rate (min
–1
) 8.5 m
Table size (W x L) 304 mm x 771 mm
No load speed (min
–1
)8,500
Overall length (W x L x H) 483 mm x 771 mm x 401 mm
Net weight 27 kg
safety class /II
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 2012 NB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2012 NB in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita 2012 NB

Makita 2012 NB User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info