782325
15
Zoom out
Zoom in
Previous page
1/60
Next page
Technical and legal
information
MSTS1500-A by MacAllister
b) Never leave the table saw unattended when in operation. Turn if off and
don't leave the tool until it has come to a complete stop. An unattended
running saw is an uncontrolled hazard.
c) Locate the table saw in a well lit and level area where you can maintain
good footing and balance. It should be installed in an area that provides
enough room to easily handle the size of the workpieces. Cluttered, dark
areas, and uneven slippery floors invite accidents.
d) Regularly clean and remove wood shavings and saw dust from under
the saw table and/or the dust extraction unit. Accumulated saw dust is
combustible and may self ignite.
e) Secure the table saw. A table saw that is not properly secured may move or
tip over.
f) Remove tools, wood scraps etc. from the table saw before turning it on.
Distraction or possible jams can be dangerous.
g) Always use blades of the right size and with the appropriate mounting
hole (e.g. starshaped or round). Blades that do not match the mounting
hardware of the saw will run off-centre, causing loss of control.
h) Only use 10" saw blade with kerf width>2.3mm and blade body thickness is
1.8 mm match the riving knife with thickness of 2 mm.
i) Always use only a saw blade diameter in accordance with the markings
on the saw; Use only saw blades for which the maximum possible speed
is not less than the maximum spindle speed of the product.
j) Never use damaged or incorrect saw blade mounting means such as
flanges, saw blade washers, bolts or nuts. These mounting means were
specially designed for your saw, for safe operation and optimum performance.
Do not use any blunt , cracked, deformed or damaged saw blades. Only
replace the saw blade with one complying with the European standard
EN 847-1.
k)Never stand on the table saw, do not use it as a stepping stool. Serious
injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
l) Make sure that the saw blade is installed to rotate in the proper direction.
Do not use grinding discs or wire brushes on a circular table saw.
Improper saw blade installation or use of accessories not recommended may
cause serious injury.
5. Additional safety instructions
- These operating instructions are intended for people with basic technical knowledge
regarding the operation of a machine like this or similar electrical power tools.
Inexperiencend persons are strongly advised to seek competent advise and
guidance from an experienced person before operating this machine.
Getting started...
15
EN
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mac Allister MSTS1500-A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mac Allister MSTS1500-A in the language / languages: English as an attachment in your email.

The manual is 4.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info