782325
13
Zoom out
Zoom in
Previous page
1/60
Next page
Technical and legal
information
MSTS1500-A by MacAllister
that your hand remains at a safe distance to the saw blade.
e) Use only the supplied push stick of the manufacturer. The push stick
provides sufficient distance of the hand from the saw blade.
f) Never use a damaged or cut push stick. A damaged push stick may break
causing your hand to slip into the saw blade.
g) Do not perform any operation"freehand". Always use either the ripping
fence or the mitre gauge to position and guide the workpiece. "Freehand"
means using your hands to support or guide the workpiece, in lieu of a ripping
fence or mitre gauge. Freehand sawing leads to misalignment, binding and
kickback.
h) Never reach around or over a rotating saw blade. Reaching for a workpiece
may lead to accidental contact with the moving saw blade.
i) Provide auxiliary workpiece support to the rear and/or sides of the saw
table for long and/or wide workpieces to keep them level. Long and/or
wide workpieces have a tendency to pivot on the table's edge, causing loss
of control, saw blade binding and kickback.
j) Feed the workpiece at a uniform speed. Do not bend or twist the
workpiece. If the saw blade jams, immediately switch off the power tool,
pull the mains plug and clear the jam. If the workpiece causes the jamming
of the saw blade, this could lead to kickback or stalling of the motor.
k) Do not remove piece of cut-off material while the saw is running. The
material may become trapped between the saw blade and fence or in the
guard and pull your fingers into the saw blade. Turn the saw off and wait until
the saw blade stops before removing the material.
I) Use an auxiliary fence for long cuts in workpieces with a thickness of
less than 2 mm. Thin workpieces may wedge under the fence and create
kickback.
3. Kickback causes and related warnings
Kickback is a sudden reaction of the workpiece due to a pinched, bound saw blade
or misaligned line of cut in the workpiece with respect to the saw blade or when
a part of the workpiece binds between the saw blade and the fence or other fixed
object.
During kickback, in most cases, the workpiece is lifted off the table by the rear
portion of the saw blade and is propelled towards the operator.
Kickback is the result of incorrect or faulty use of the table saw. It can be prevented
if suitable precautionary measures are taken as described below.
Getting started...
13
EN
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mac Allister MSTS1500-A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mac Allister MSTS1500-A in the language / languages: English as an attachment in your email.

The manual is 4.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info