782325
14
Zoom out
Zoom in
Previous page
1/60
Next page
a) Never stand directly in line with the saw blade. Always position your
body on the same side of the saw blade as the fence rail. Kickback may
propel the workpiece at high velocity towards anyone standing in front and
in line with the saw blade.
b) Never reach over or in behind the saw blade to pull or support
the workpiece. Accidental contact with the saw blade may occur or kickback
may drag your fingers into the saw blade.
c) Never hold and press the workpiece that is being cut off against the
rotating saw blade. Pressing the workpiece being cut off against the saw
blade will create a binding condition and kickback.
d) Align the fence rail to be parallel with the saw blade. A misaligned fence
will pinch the workpiece against the saw blade and create kickback.
e) Use a featherboard to guide the workpiece against the table and fence
rail when making hidden cuts (e.g. seaming). A featherboard helps to
control the workpiece in the event of a kickback.
f) Be particularly careful when sawing in areas of joined workpieces that
you cannot see. The plunging saw blade can saw into objects that could
cause kickback.
g) Support large panels to minimise the risk of blade pinching and kickback.
Large panels tend to sag under their own weight. Supports must be placed
under the panel on both sides, near the line of cut and near the edge of the
panel.
h) Use extra caution when cutting a workpiece that is twisted, knotted,
warped or does not have a straight edge to guide it with a mitre gauge
or along the fence rail. A warped, knotted, or twisted workpiece is unstable
and causes misalignment of the kerf with the saw blade, binding and kickback.
i) Never cut more than one workpiece, stacked vertically or horizontally.
The saw blade could pick up one or more pieces and cause kickback.
j) If you wish to restart a saw that is stuck in the workpiece, centre the
saw blade in the kerf and check whether that the saw teeth are not caught
in the workpiece. If the saw blade binds, it may lift up the workpiece and
cause kickback when the saw is restarted.
k) Keep saw blades clean, sharp, and with sufficient set. Never use warped
saw blades or saw blades with cracked or broken teeth. Sharp and properly
set saw blades minimise binding, stalling and kickback.
4. Safety instructions for table saws
a) Turn off the table saw and unplug it when removing the table insert,
changing the saw blade or making adjustments to the riving knife, anti-
kickback device or saw blade guard, and after each completed cutting
procedure. Precautionary measures serve to avoid accidents.
Technical and legal
information
MSTS1500-A by MacAllister
14
Getting started...
EN
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mac Allister MSTS1500-A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mac Allister MSTS1500-A in the language / languages: English as an attachment in your email.

The manual is 4.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info