708397

Lumag HGM-85055 Manual

21
Zoom out
Zoom in
Previous page
1/36
Next page
-15-
(GB)
VI.
Operating the Machine
The machine is intended for maintenance of irregularly mowed grass areas. The mulching machine disintegrates the
vegetation into small pieces that remain evenly distributed in place. Grass remains thus do not cumulate in one place an
d sere as
natural fertilizer.
2. Mulching Process
Mulching frequency: Perform mulching 3-4 times per year. First mulching should be performed at the beginning of the
vegetation season; last mulching should be performed at the end of the vegetation season. Other mulching depends on grass
growth conditions.
Mulching method: Use a single phase for mulching of grass up to 25 cm – adjust the knife height depending on grass
vegetation quality.
Grass exceeding 25 cm should be mulched in two phases, Fig. 10. Adjust the knife height to the higher position No. II, Fig.
4, for the first phase.
It is possible to lower the knife height to position No. I, Fig. 4, during the second phase.
2. Mowing Height Adjustment
Stubble height can be adjusted by rearranging the two soles (1) fitted to the mulching tunnel through bolt connections.
The stubble height can be adjusted in two position, the basic position No. I, and by readjusting soles in position No. II. Fig. 4.
Stubble height adjustment in position No. II.
Loosen the bolt with nut (2) in the front sole part, loosen and unscrew the bolt (3) in the rear sole part. Shift the rear sole part
so that the sole opening overlaps with opening No. II on the tunnel. Run the bolt (3) through both openings and the saddle
washer (4). Screw-in the self-locking nut from the inner tunnel side and tighten the connection. Then tighten the bolt with
self-locking nut (2) in the front sole part.
Perform the same procedures when rearranging the second sole. Both soles must be adjusted to the same height! Fig. 4.
Thus, the machine can be adjusted to a specific terrain.
3. Mulching Machine Drive
Adjust the accelerator control lever (3), Fig. 3, to the “START” position for a cold engine, to the “MAX” position for a warm
engine and start the engine. Observe instructions provided in the instructions for use of the engine throughout the operation.
The accelerator is located in the central section of the upper handlebar part.
During engine start-up, both clutch levers on the handlebars need to be released. Adjust max. engine revolutions by the
accelerator lever.
Grab the handlebar grip. Press the lever (2), Fig. 3, on the right handlebar side. Keep pressing the lever up to two travel thirds
very slowly in order for the mowing knife to be able to start turning and the engine not stopping. ♠Knife start-up is
accompanied by partial slipping of the vee-belt and the related effects (rattling, whistling). Upon start-up of the mowing
knife, press the lever completely toward the handle.
Engaging of the drive is performed by a lever (1), Fig. 3, on the left handlebar side. Press the lever to the handle and the
machine starts moving.
5. Stopping the Mulching Machine
Release the left lever and the machine stops. The mowing knife drive is shut down immediately upon release of the right
lever. The safety brake stops the mowing knife within a very short time. During turning or backward movement with the
machine it is not necessary to stop the mowing knife in order to prevent wasting of energy of the spinning mowing knife. The
engine is stopped by moving the accelerator lever (3), Fig. 3, to position “0”.
In case of a critical situation, immediately release both levers on the handlebar. The levers return to the zero position, the
drive and the mowing knife come to a halt.
VII.
Adjustment and Maintenance
1. Replacement of the Mowing Knife
Loosen and unscrew the knife bolt (1) with the washer (2), knife washer (3) and the disk washer (4) that fixes the
mulching knife (5) to the knife nave (6). Have the knife sharpened or exchange it. Perform assembly in reverse order of Fig.
8.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lumag HGM-85055 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lumag HGM-85055 in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info