599356
14
Zoom out
Zoom in
Previous page
1/24
Next page
$ENSfliV!TY
I
Figure
8 GRAYLINE
"orr"
Figure
9
PROPER SETTING
8= ENABLE DIGITAL
AVERAGING
9= DISABLE DIGITAL AVERAGING
The
digital
sonar in the X-50 is a
highly
sensitive sonar that
gives
extremely rapid updates
of the water
depth.
Under most
conditions,
the
bottom contour
changes
so
rapidly
that the
depth display
can
appear
to
"jitter".
In other
words,
the
display
will
change
the
depth
so
quickly
that it
can be difficult to determine the actual bottom
depth.
To alleviate this
situation,
the X-50 can
average
the bottom
readings
and
place
the result
on the
display.
When the X-50 is first turned
on,
averaging
is enabled. To
disable
averaging, press
the 9
key
once the menu
appears.
To enable
averaging
once
again, press
the 8
key.
10
=
BATTERY BACKUP ENABLED
11
=
BATTERY BACKUP DISABLED
The X-50
has
battery
backed
up
memory
which allows it to retain all
settings
even if the
power
cable is removed from the unit. The
battery
can
be turned off or
back on at
anytime.
When the X-50 is
shipped
from the
factory,
the
battery
is turned on. To
turn it
off, press
11. To turn it on
again,
press
iO.
I
stow
STOP
FAST
[
RECALL
RESUME
STORE
CHART SPEED
When the X-50 is
turned on for the first
time,
the chart scrolls at
a
pre-determined speed.
If a
higher speed
is
desired, press
and hold the
FAST
key
in the CHART
section of the
keyboard
until it runs at the desired
speed.
To slow the
display, press
and hold the SLOW
key.
Whenever either
of these
keys
are
pressed,
the
sensitivity
bar at the
top
of the
display
will
change
to a dashed
line and the word "CHT" will
replace
the word
"AUTO" near the
top
of the
display.
The dashed bar
represents
the chart
speed.
If
you press
and hold the FAST
key
for
example,
the
bar will start
moving
to the
right, signifying
that the chart
speed
is
increasing.
There are
10
steps
of chart
speed.
When the horizontal bar
reaches the
far
right
side
of the
screen,
the chart
speed
is at its maximum
value. The X-50 will
"flutter"
signifying
the maximum chart
speed
has been reached.
lithe automatic mode or
digital
function is
on,
the maximum chart
speed
cannot be attained.
(The
chart bar will
stop
two
steps
from
the far
right
and the audible tone will
"flutter".) Turning
both the
digital
and the
automatic mode off will allow
the maximum chart
speed
to be attained.
(Ten steps
of chart
speed
are available if the
digital
and AUTO are
off,
Eight
steps
of charts
speed
available
with
digital
and AUTO
on.)
12
=
SCALE ON
13
=
SCALE OFF
The
upper
and lower limit numbers on the
right
side of
the
display
can
be turned on or off
as desired. When the X-50 is
shipped
from the
factory,
the scales are turned on. To turn
them
off,
press
13 after the
menu
appears.
To turn
them
back on
again, press
12.
14
=
CALIBRATE SPEED
Due to
variations in boat hulls
and sensor
mounting locations,
the
speedometer
on the X-50
may
need to
be calibrated. The X-50
allows
corrections to be
entered
using
the CALIBRATE
SPEED command.
To use
it,
press 2nd,
DISC
(COMMAND)
until the
CALIBRATE SPEED function on
the menu
appears.
Then
press
14.
12
33
PDF compression, OCR, web-optimization with CVISION's PdfCompressor
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance X-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance X-50 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info