599356

Lowrance X-50 Manual

16
Zoom out
Zoom in
Previous page
1/24
Next page
To use the scale markers with a
zoom,
simply
subtract the
upper
limit
from the lower
limit,
then divide that number
by
ten to
get
the number of
feet
per
line. For
example,
if a
target
is on the third line and the
upper
limit
is 120 feet with a lower limit of 160
feet,
then subtract 120 from 160 which
equals
40. To
get
the number of feet
per
mark,
divide 40 feet
by
10 lines
which
equals
4. Now
multiply
4 times 3
(target
is at the third
line)
and
you
get
12. Add
120
(upper limit)
to
12 and
the
depth
of the
target
is 132
feet
deep.
RANGE
When
the X-50 is in the automatic
mode,
the
ranges
will
automatically
change
to
keep
the bottom
signal
on the
display
as the bottom
depth
changes.
At
times, however,
it
may
be desirable to
expand
the
range
or
zoom in on a
target.
The
upper
limit can be set from 0 to 6490 feet and the
lower limit can be set from 10 to 6500 feet
Any
combination of the two
limits
may
be
used,
provided
that the lower limit is no closer than ten feet to
the
upper
limit. If a
segment
less than ten feet is
entered,
the X-50
will
'flutter" and the
range
will remain at the
previous setting.
(Note:
Maximum
depth capability
will
depend upon
the water and
bottom
conditions,
type
of
transducer,
and
quality
of transducer
installation.)
LOWER
LIMIT
LOWER
LIMIT
Automatic
Operation
When the X-50 is first turned
on,
it will
automatically
find and
display
the
bottom
signal, picking
a lower
limit
that
will
put
the bottom
signal
in
the
lower
portion
of the
display.
As the bottom
depth changes,
the X-50 will
automatically change
the lower limit to
keep
the bottom
signal
on the
display.
When the X-50
changes
ranges
while in the automatic
mode,
the
lower limit
selected
will
always
be
a
multiple
of ten.
In other
words the
lower limit will be a number that ends in zero such as
ten,
twenty, forty,
one
hundred,
etc.
The lower limit
may
be
changed
while the X-50 is in the automatic
mode,
however the lower limit cannot be set shallower than the bottom. If a
lower limit is chosen that is less than the bottom
depth,
the X-50 will
ignore
the command.
To
change
the lower limit while the X-50 is in the automatic
mode,
simply press
the desired
depth,
then
the
LOWER
LIMIT
key.
For
example,
changing
the lower limit to 50 feet
requires
the
following keys
to be
pressed: 5, 0,
LOWER LIMIT
o
=
FASTRAK ON
1
=
FASTRAK OFF
FASTRAK is
a
feature that converts all echoes to short horizontal bars
on the far
right
side of the
display.
The
graph display
continues
to
operate
normally,
however In
essence,
FASTRAK is a vertical bar
display
that
enables
you
to determine a
target's depth
easier For
example,
see
figure
30 above. With FASTRAK
enabled,
the fish echo is
making
a mark close to
the 8th line on the scala With an
upper
limit of 0 and a lower limit of
eo,
then each scale mark is 6 feet which
places
the fish at
approximately
54
feet. Since FASTRAK is so close to the scale
markers,
it makes it a little
easier to line
up
the
targefs depth
with the scale.
To turn FASTRAK
on, press
the 0
key.
To turn FASTRAK
off,
press
the 1
key.
14
31
-
S
I
H
hi
I-
H
-52,Q
F
"'i—i
PDF compression, OCR, web-optimization with CVISION's PdfCompressor
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance X-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance X-50 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info