Manual LivarnoLux IAN 113911 (page 8 of 61) (English, German, Dutch, Danish, French, Swedish, Finnish)

649223

Zoom out

Zoom in

1/61

8 GB/IE

Initial useSafety / Preparation / Prior to installation / Initial use

Avoid battery ﬂuid coming into contact with the

skin, eyes and mucous membranes. In the event

of contact, immediately rinse the aﬀected area

with plenty of clear water and seek immediate

medical attention.

Preparation

Required tools and material

The tools and materials speciﬁed are not included.

This information and these values are non-binding

and are only provided as a reference. The nature

of the material is determined by the individual local

conditions.

– Pencil / marking tool

– Voltage tester

– Screwdriver

– Electric drill

– Drill bit (approx. Ø 6 mm)

– Hammer

– Side cutter

– Ladder

Prior to installation

Important: The electrical connection must be per-

formed by a trained electrician or a person instructed

in electrical installation. This person must be familiar

with the properties of the light and connection reg-

ulations.

Do not remove the decals on the light (marking A,

B, C, etc.) used as an installation guide, after com-

pleting installation.

Familiarise yourself with all the instructions and

illustrations in this manual, as well as with the

light itself, before installing it.

Prior to installation, verify the circuit to which the

light will be connected is not energised. To do s

remove the fuse or switch oﬀ the circuit breaker

in the fuse box (0 position).

Use the voltage tester to verify the de-ener-

gised status.

Initial use

Mounting / installing the light

(see Fig. A–D)

ATTENTION! Do not remove the decals on the

light

(marking A, B, C, etc.) used as an installa-

tion guide, after completing installation.

The LED ceiling light

is constructed as a

sealed system, thus fully assembled. Do not

open the LED ceiling light

for installation.

Prior to installation, verify the circuit to which

the light will be connected is not energised. To

do so, remove the fuse or switch oﬀ the circuit

breaker in the fuse box (0 position).

Centre the unprinted side of the mounting tem-

plate

over the mains connection cable

and determine the position of your LED ceiling

light

on the ceiling. Be sure the logo for the

terminal block

is located near the exit for the

mains cable

. The mains cable

should

ideally be at least 15 cm long.

Mark the three bores (1, 2, 3)

using the

mounting template

and apply the included

decals (A, B, C)

to the ceiling congruent

with the recess on the side edge (A, B, C) of the

mounting template

. You may now remove

the mounting template

Drill the holes (1, 2, 3). Be sure not to damage

the supply line.

Insert the wall plugs

into the bores. If neces-

sary, use a hammer.

Screw the included screws

into the wall

plugs

so they still protrude approx. 8 mm

from the ceiling.

Insert the three building wires in the terminal

block

of the LED ceiling light

as indicated

by the colours and screw down.

Note: Be sure to connect the individual wires

of the mains cable (external)

correctly:

live wire, black or brown = symbol L,

neutral wire, blue = symbol N,

earth wire, green-yellow = symbol

After wiring to the building wiring, align the LED

ceiling light

as follows: the decals (A, B, C)

on the LED ceiling light

must match the

decals (A, B, C)

on the ceiling. The screw

screw holes

on the back of the LED ceiling

After 3 years of use the lamp has started blinking when switched on. The installation is fine, coul it be the transformer. Is it possible to replace it? Submitted on 27-4-2020 at 19:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of LivarnoLux IAN 113911 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 0,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

LivarnoLux IAN 113911 Manual

Product: