612980
15
Zoom out
Zoom in
Previous page
1/41
Next page
Chapter 3
Advanced Configuration
12
Wireless-N Access Point with Dual-Band
RTS Threshold Should you encounter inconsistent data
flow, only minor reduction of the default value, 2347, is
recommended. If a network packet is smaller than the
preset RTS threshold size, the RTS/CTS mechanism will not
be enabled. The Access Point sends Request to Send (RTS)
frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the
wireless station responds with a Clear to Send (CTS) frame
to acknowledge the right to begin transmission. The RTS
Threshold value should remain at its default value of 2347.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Administration > Management
Use this screen to manage specific Access Point functions:
access to the browser-based utility, backup of the
configuration file, and reboot.
Administration > Management
Access Point Access
To ensure the Access Point’s security, you will be asked for the
Access Point’s password when you access the Access Point’s
browser-based utility. The default password is admin.
Access Point Password Enter a new Password for the
Access Point.
Re-enter to confirm Enter the Password again to confirm.
Idle Timeout The login times out after a period of
inactivity that you specify. The range is 60 to 3600 seconds.
The default is 600.
Local Management Access
Access via Wireless If you are using the Access Point in
a public domain where you are giving wireless access to
your guests, you can disable wireless access to the Access
Points browser-based utility. If you do this, you will only
be able to access the browser-based utility via a wired
connection. Keep the default, Enabled, to allow wireless
access to the Access Points browser-based utility, or select
Disabled to block wireless access to the utility.
Backup and Restore
Backup To back up the Access Point’s configuration
settings, click Backup Configurations. Then follow the
on-screen instructions.
Restore To restore the Access Point’s configuration
settings, click Browse and select the configuration file.
Then click Restore Configurations. (You must have
previously backed up the Access Point’s configuration
settings.)
System Reboot
Reboot To reboot or restart the Access Point, click Start
to Reboot.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Administration > Factory Defaults
Use this screen to restore the Access Point’s configuration
to its factory default settings.
Factory Defaults
Restore All Settings To reset the Access Point’s settings
to the factory defaults, click Restore All Settings. Any
settings you have saved will be lost when the default
settings are restored.
Administration > Factory Defaults
Administration > Firmware Upgrade
Use this screen to upgrade the Access Points firmware.
Do not upgrade the firmware unless you are experiencing
problems with the Access Point or the new firmware has a
feature you want to use.
Administration > Firmware Upgrade
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys WAP610N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys WAP610N in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info