727826
29
Zoom out
Zoom in
Previous page
1/77
Next page
25
DHCP
Linksys
25
DHCP
DHCP
DHCP is a network protocol used to configure devices that are connected to a
network so they can communicate on that network using the Internet Protocol (IP).
You could set up the DHCP server or DHCP relay, and view the DHCP status.
DHCP Setup
An embedded DHCP server supports automatic IP assignation for LAN computers.
(This function is similar to the DHCP service in NT servers.) It benefits users by
freeing them from the inconvenience of recording and configuring IP addresses
for each PC. When a computer is turned on, it will acquire an IP address from the
device automatically.
NOTE Remember to click Save before leaving the page. You can also click
Cancel to undo the changes.
Click the IPv4 tab or the IPv6 tab.
IPv4:
VLAN: Choose the VLAN.
Device IP: This is the default device IP.
Subnet Mask: Input the subnet mask of the static IP address issued by
ISP.
There are three DHCP modes: None, DHCP Server, and DHCP Relay.
DHCP Server: Check the option to enable the DHCP server automatic IP
lease function. When enabled, all PCs will be able to acquire IP automatically.
Otherwise, users should configure static virtual IP for each PC
DHCP Relay: Check the option to enable the DHCP relay function. DHCP relay
is a proxy that is able to receive a DHCP request and resend it to the real DHCP
server.
DHCP Server IP Address: This is the current DHCP IP.
Client lease Time: This is to set up a lease time for the IP address
acquired by a PC. The default is 1,440 minutes
(one day). Users can change it according to their
needs. The time unit is minutes.
Range Start: The initial IP automatically leased by DHCP. The
default initial IP is 192.168.1.100.
Range End: Thefinal IP automatically leased by DHCP. The
default initial IP is 192.168.1.149.
DNS Server: You could use DNS proxy, DNS from ISP, or
configure your own DNS below.
Static DNS 1: Input the IP address of the DNS server.
Static DNS 2: Input the IP address of the DNS server.
WINS Server: Input the IP address of WINS.
IPv6:
Enable DHCP Server: Check the option to enable the DHCP server
automatic IP lease function. When enabled,
all PCs will be able to acquire IP automatically.
Otherwise, users should configure static virtual IP
for each PC.
Client lease Time: This is to set up a lease time for the IP address
acquired by a PC. The default is 1,440 minutes
(one day). Users can change it according to their
needs. The time unit is minutes.
Range Start: The initial IP automatically leased by DHCP. The
default initial IP is 192.168.1.100.
Range End: The final IP automatically leased by DHCP. The
default initial IP is 192.168.1.149.
DNS Server (required) 1: Input the IP address of the DNS server.
Static DNS 2: Input the IP address of the DNS server.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys LRT224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys LRT224 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info