Manual Liebherr SBSes 8496 (page 15 of 30) (English)

715385

Zoom out

Zoom in

1/30

Insert the holder with its cable into the opening.

Fig. 36 (5)

Press the holder downwards until the tab clicks into place.

Fig. 36 (6)

Insert the plugs.

Fig. 36 (7)

4.3.13 Fitting the cable connection

Fig. 37

Engage the plug above the upper bearing bracket and care-

fully place the cable strands into the channel.

Fig. 37 (1)

Carefully position the grey cable in the guide above the top

bearing bracket.

Fig. 37 (2)

Fig. 38

Insert the grey cable into the guide in the top door.

Fig. 38 (1)

Engage the plug.

Fig. 38 (2)

Position the remaining cable length as a loop in the guide, if

required.

4.3.14 Aligning the doors

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

Screw the turn hinges firmly into place with 4 Nm.

Check all of the screws and retighten if necessary.

Align the doors flush with the appliance housing using the

two oblong holes in the lower bearing bracket and centre

bearing bracket if needed. To do this undo the middle screw

in the bottom bearing bracket with the T25 tool supplied.

Undo the remaining screws a little with the T25 tool or with a

T25 screwdriver and align using the slotted holes. Undo the

screws in the middle bearing bracket with the T25 tool and

align the middle bearing bracket using the slotted holes.

Support the door: Take off the adjustable foot on the bearing

bracket using the open-ended wrench SW10 until it comes

into contact with the floor, then turn an additional 90°.

4.3.15 Fit the bottom soft stop mechanism

Fig. 39

Slide the soft stop mechanism on the bearing bracket side at

an angle into the slot as far as the limit stop.

Fig. 39 (1)

Slide the soft stop mechanism fully into the slot.

Fig. 39 (2)

The unit is positioned correctly when the rib on the soft stop

mechanism is in the guide.

Tighten the screw with the T15 screwdriver.

Fig. 39 (3)

Push the cover over the hinge.

Fig. 39 (4)

Fig. 40

The door is open 90°

Turn the hinge in the mount.

Fig. 40 (1)

Insert the bolt with a T15 screwdriver in the mount and

hinge. Make sure that the catch mechanism is sitting

correctly in the groove.

Fig. 40 (2)

Push the bearing bracket cover along the hinge and fit on

the mount.

Fig. 40 (3)

Remove the locking device.

Fig. 40 (4)

Position the panel on the handle side and swing it in.

Fig. 40 (5)

The panel is clicked into place.

Close the bottom door.

Putting into operation

* Depending on model and options 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr SBSes 8496 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr SBSes 8496

Liebherr SBSes 8496 Installation Guide - German - 6 pages

Liebherr SBSes 8496 User Manual - German - 30 pages

Liebherr SBSes 8496 User Manual - Dutch - 62 pages

Liebherr SBSes 8496 User Manual - French - 26 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr SBSes 8496 Manual

Product: