17480

Kyocera KM5530 Manual

220
Zoom out
Zoom in
Previous page
1/250
Next page
Section 9 TROUBLESHOOTING
9-2
Message
“Place transparency in bypass.”
[“Place transparencies on stack
bypass.”]
“Check paper size.”
“Reposition original.”
“Check paper size. Copy paper is
not the same size as original.”
[“Paper size in cassette differs from
actual size. Check paper size in
cassette.”]
“Reposition original or change
drawer.” [“Reset original or select
another paper cassette.”]
“Check paper size in tray. Different
from original.” [“Check paper size in
cassette. Different from original.”]
“Reset originals in processor.”
“Reset all originals in processor.”
[“Reset originals in processor.”]
“Press start key for job recovery.”
[“Press Start key to resume
copying.”]
“Too many pages in processor.
_____:maximum capacity”
[“Too many pages in the processor.
_____:max. number of original.”]
“Original left on platen. Remove
original.” [“Original is left on platen.
Remove original.”]
“Reset all originals in Document
processor.” [“Reset originals in
Document processor.”]
“Remove originals from processor.
Set mode is not available when
using Doc Processor.”
[“Remove originals from processor.
The set mode is not available when
using Doc Processor.”]
“Interrupt copying is not available for
this size.”
“These functions cannot be
combined.”
Procedure
Load transparencies onto the multi-bypass tray.
There is no paper loaded of a size that can be used in the currently selected mode.
Check the paper.
The orientation of the original and the selected paper are different. Change the
orientation of the original. If you press the [Start] key without changing the original,
copying will be performed at a 100% (1:1) magnification ratio.
Load paper of the size selected or change the selection for the paper size.
The orientation of the original and the selected paper are different. Change the
orientation of the original.
Load paper of the size selected or change the selection for the paper size.
Remove the originals from the Document Processor, stack them together cleanly and
reset them in their current order back in the Document Processor.
Remove the originals from the Document Processor and reset them in their original order
back in the Document Processor.
Copying will be resumed from the point it was stopped. Press the [Start] key.
The number of originals in the Document Processor has exceeded the acceptable limit.
Reset a lesser number of originals.
An original has been left on the platen or in the Document Processor. Remove the
original.
Remove the originals from the Document Processor.
Remove the originals from the Document Processor and set them one by one on the
platen.
Interrupt copying is not possible. Use different originals or cancel the interrupt copying
operation and try to copy again later.
The function or mode that you just selected cannot be used in combination with the
currently set function or mode.
Reference
page
3-4
—
—
7-23
—
—
—
—
—
—
—
—
—
—
—
… 220 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera KM5530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera KM5530 in the language / languages: English as an attachment in your email.

The manual is 8,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info