635791

Kubota KX91-3 Manual

82
Zoom out
Zoom in
Previous page
1/98
Next page
OTHER ADJUSTMENTS AND REPLACEMENTS62
A Track seam
The ends of the rubber track are joined with a seam.
When adjusting the tracks, the seam must be
positioned on the top midway between the idler and
the sprocket. By machines equipped with an upper
roller, the seam mark should be positioned over the
upper roller.
If the seam is positioned incorrectly, the tracks will be
tensed to loosely, and a further readjustment will be
necessary.
A Rotate the track after adjustment one to two times to
check the tension. To loosen the rubber tracks, follow
the same method as for steel tracks.
A Additionally following points are to be observed when
adjusting rubber tracks.
(1) If the track slackens more than 25 mm, readjust
them.
(2) Check track tension 30 hours after initial use and
readjust if necessary. Check and adjust thereafter
every 50 service hours.
BSpecial Information when Using Rubber
Tracks
1. When turning, make a slow swing turn. Avoid spin
turns to reduce lug wear and entry of dirt.
2. The relief valve may be activated if too much dirt and
sand clog the tracks. In this case move the machine for
a short distance straight backwards to let the earth and
sand fall off, then a turn can be made.
3. Avoid using rubber track on riverbeds, stony
underground, ferro-concrete and on iron plates. The
rubber can damage as well as increase wear on the
tracks.
BSteel Tracks
C Track shoe plate tension
1. Loosen bolt (1) and remove the cover (2).
2. Apply grease (4) to the grease nipple (3).
3. To check the track tension, the track must be lifted
from the ground as shown. The track tension is correct
if the clearance between the outer end of the track
roller and the track interior surface corresponds to the
dimension specified in the table below.
To avoid serious injury or death:
A Do not work under the machine in this
condition.
A For your safety do not rely on hydraulically
supported devices, they may leak down and
suddenly drop or be accidentally lowered.
(1) Bolt
(2) Cover
(3) Grease nipple
(4) Grease gun (Option)
(1) Drive sprocket
(2) Idler
(A) 75 to 80 mm
… 82 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kubota KX91-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kubota KX91-3 in the language / languages: English as an attachment in your email.

The manual is 11,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info