693399
50
Zoom out
Zoom in
Previous page
1/58
Next page
rev. 0/2018
lares 4.0 PROGRAMMING MANUAL
50
Type: Remote control
The subtypes available are:
• Switch-off pressing: sends a message by pressing the off button on the remote control (short press).
• Partial button pressing: sends a message by pressing the partial key on the remote control (short press).
• Pressing the Total button: runs the scenario by pressing the Total button on the remote control (short pressing).
• Long pressing of the off button: sends a message by pressing the off button on the remote control (long press).
• Partial button long pressing: sends a message by pressing the partial button on the remote control (long press).
• Total button long pressing: sends a message by pressing the total button on the remote control (long press).
• Long pressing of the "
i" button: sends a message by pressing the (i) button on the remote control (long press).
Type: Key ID
The subtypes available are:
• Code recognized: sends a message when a code is recognized. Valid option for codes entered on the keypad or APP.
• Key recognized: sends a message when a "Key" is enabled on the reader (on keypad or flight/flight-IN).
Type: Motherboard
The subtypes available are:
• Tamper: sends a message when there is a tamper condition of the metal box of the control panel (opening and / or
detachment from the wall) detected by means of the switches connected to the connector "t" of the "lares 4.0" card.
• Tamper reset: sends a message when the tamper condition of the control panel box is reset.
• Start of maintenance: sends a message when a new configuration is applied.
• End of maintenance: sends a message when the programming of parameters, through portal or installer APP, is
completed
• Periodic test: sends a message based on the scheduled periodic event (test event)
• Wrong code: sends a message after three incorrect codes are entered on the keypad. After four incorrect codes the
keypad is blocked for (90s.).
• Installer PIN recognized: sends a message when the installer code is recognized.
• Control panel off: sends a message when a switch-off event of the controlled system occurs (the 230V power supply is
missing and the battery is discharged). In this case we should preserve the battery from total discharge.
• Control panel reset: sends a message when the control panel is restarted because it has been removed and then the
power is restored or due to a system failure or a firmware update.
• Ethernet network failure: sends a message when the Ethernet cable is disconnected (or when the router/switch is
turned off).
• Ethernet network reset: sends a message when the Ethernet cable is reconnected (or when the router/switch is turned
on).
• PSTN network failure: sends a message when the telephone line is removed from the PSTN module (cable cut or line
fault).
• PSTN network restore: sends a message when the telephone line on the PSTN module is restored.
• GSM network failure: sends a message when the GSM network is missing (no signal, GSM repeater malfunctioned or
switched off for maintenance, SIM disabled and no longer registered on the network of the mobile operator).
• GSM network reset: sends a message when the GSM network is restored.
• Failed superv. IP receiver: sends a message when it fails to send supervision from the IP receiver.
• IP receiver reset: sends a message when the IP receiver responds to the supervision packets.
• Wireless jamming: sends a message when the control panel's wireless receiver or one of the "duo" transceivers detects
a disturbance on the 868MHz frequency.
• Wireless jamming restored: sends a message when the disturbance on the 868Mhz frequency, detected by the wireless
receiver of the control panel or one of the "duo" transceivers, ceases to exist.
50


Need help? Post your question in this forum.

Forumrules
1

Forum

ksenia-lares-4.0

Reset search

  • Hi
    We have a message peripherals lost. What does this mean? Submitted on 24-7-2021 at 08:15

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ksenia Lares 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Lares 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info