Manual Kress 1400 HKS (page 19 of 184) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

508068

Zoom out

Zoom in

1/184

Operation English 19

1400HKS,1400DS-EN / 1106

Swing guard

 When the saw blade is applied to the work-

piece, the swing guard (11), which covers the

saw blade, moves back automatically at the

same speed at which the blade is applied.

When you reach the end of the cut, the swing

guard moves back under spring pressure to

cover the blade again.

Setting the cut depth

 The cutting depth can be set up to 66 mm

(1400 HKS).

 The cutting depth can be set up to 200 mm

(1400 DS).

 By releasing the clamp lever (7) on the housing,

the base (14) can be pressed downwards and

thus moved in the direction of cutting depth "0."

 The cutting depth can be read off on the indi-

cator (24) or reset according to the scale.

Sawing to layout lines

 On the front edge of the circular saw base,

there is a marker (indentation) for right-angled

cuts (zero setting) corresponding to the saw

blade width. There are also marking tongues

for 0° and 45° bevel cuts. These enable simple

and precise operation.

 The marking tongues in the base of the circular

saw (see drawing) also correspond to the cut

width of the saw blade.

Fitting the saw blade

 Move the motor of the circular saw to its highest

position (min. cutting depth) – as described

under Setting the cutting depth – by releasing

the clamp lever (7) and then re-securing the

clamp lever (7).

 Pull the swing guard (11) back and hold it in

end position.

 Then fit the individual parts onto the drive

spindle of the saw in the following order:

1. Flange (20)

2. Saw blade (18)

3. Thrust washer (22)

4. Washer (21)

5. Socket-head cylinder bolt M8 x 18 (23)

 Press and hold down the pin for spindle lock

(19), and if necessary, rotate the saw blade

until the lock snaps into place.

 With the pin for spindle lock (19) pressed down,

tighten the socket-head cylinder bolt (23) with

the hex key (13).

 To replace the saw blade, carry out the same

steps in reverse order. Fit the new blade as

described.

Fitting the riving knife

 Leave the motor of the circular saw in the

same position (min. cutting depth) as was

required to fit the saw blade.

 Attach the riving knife (12) using the socket-

head bolt (16) and the washer provided. At first,

only tighten the socket-head bolt (16) lightly.

 Adjust the riving knife (12) so that the dis-

tance to the tips of the saw teeth and to the

lowest point of the saw blade is max. 5 mm

(see Figure). The distance to the toothed rim

of the saw blade must not exceed 5 mm.

-NOTE-

The cutting depth should always match the thick-

ness of the workpiece, i.e. the blade should only

protrude from the material by approx.the height of 1

saw tooth. This is important in order to prevent

accidents!

-NOTE-

When sawing along a layout line, please ensure

that you cut according to the left or right edge of

the indentation or marking tongue, depending on

whether you are sawing to the left or right of the

layout line.

Changing the tool

-NOTE-

When inserting the blade, make sure that the

direction of the arrow on the saw blade corre-

sponds to the direction of the arrow on the housing.

The bearing surfaces of the saw blade, flange and

washer must be clean.

-NOTE-

This kickback safety device must be fitted!

36727_a_BA_Handkreissäge_1400HKS.book Seite 19 Donnerstag, 20. Oktober 2011 9:25 09

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kress 1400 HKS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kress 1400 HKS Manual

Product: