508068
18
Zoom out
Zoom in
Previous page
1/184
Next page
18 English Operation
1400HKS,1400DS-EN / 1106
EN
The vibration emission level will vary because of
the ways in which a power tool can be used and
may increase above the level given in this infor-
mation sheet. This could lead to underestimation
of vibration when the tool is used regularly in such
a manner.
Noise levels and vibration 1400 DS: see assembly
instructions "Chain saw attachment"
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given
period of work should also take into account the
times when the tool is switched off and when it is
running but not actually when doing the job.
This may significantly reduce the exposure level
over the total working period.
Specify additional safety measures to protect the
operating personnel against the effects of vibra-
tion, for example: Maintenance of power tools and
accessories, keeping hands warm, organisation of
workflows.
4. Operation
Before putting into operation, check that the mains
voltage and frequency on the identification plate
match the details of your mains supply.
Mains cable module
Connect the mains cable module (9) to the handle.
The plug must snap in.
Only use the mains cable module (9) for Kress
power tools. Do not attempt to operate other
machines with the module.
Damaged mains cable modules must not be used.
They must be replaced with a new Kress mains
cable module immediately.
Press the two unlocking buttons (10) and remove
the mains cable module (9) from the handle.
Use only an original Kress mains cable module
and at least a heavy rubber tube cable (H05 RN-F).
Switching on and off
Before pressing the On/Off switch (1) in the
handle, the switch must be unlocked by
pressing in the release switch (2). Only then
can the saw be put into operation by pressing
the On/Off switch.
When the On/Off switch is released, the power
supply is interrupted and the saw comes to a
standstill. The lock off safety position auto-
matically locks the switch and prevents the
saw being switched on unintentionally.
Base
The base (14) has been fitted at the factory so
that the angle between the base and the saw
blade in basic position (zero setting) is pre-
cisely 90°. The 4-point mounting guarantees
accurate operation.
Before carrying out any work on the
machine, pull the main plug.
Start-up
Observe correct main voltage!
If using an extension cable: Only use
extension cables specifically approved
for the application with the required
cross-section. Otherwise the power of
the tool can be reduced and the cable
can overheat. Replace damaged
extension cables.
Mains cable
If the mains cable is damaged while
working, pull the mains plug immedi-
ately.
Mains cable module with Patent
Quick Interlock.
Operation
-WARNING-
Saw blade and riving knife (12) must be fitted before
starting up the saw. Observe the corresponding
information in these operating instructions! The
riving knife (12) serves as a protection against
kickback, and it is thus imperative to fit it!
-NOTE-
For safety reasons, it is not possible to lock the
On/Off switch in position for continuous operation.
36727_a_BA_Handkreissäge_1400HKS.book Seite 18 Donnerstag, 20. Oktober 2011 9:25 09
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress 1400 HKS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress 1400 HKS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info