508063
18
Zoom out
Zoom in
Previous page
1/170
Next page
18 English Operation
FME-EN / 0904
EN
Switching On and Off
To switch on the machine, push the On/Off switch
5 forward and press it down at the front to lock on.
To switch off the machine, press down the On/Off
switch 5 at the rear so that the switch springs back
to the off position.
Preselect speed (Option)
In devices with a setting dial 6, you can select the
speed using the setting dial 6 depending on the
area of application.
Clamping the tools
The spindle 3 of the milling and grinding motor is
equipped with a precision collet chuck 2 to hold
the tools. A spindle lock enables you to tighten
and loosen the locknut 1.
To clamp the tool, you lock the spindle 3 by
pressing the locking button 4.
You tighten the locknut 1 using a SW 17
open-ended spanner.
When you unclamp the tool, the spindle 3 in
turn is locked.
You loosen the locknut 1 by turning the open-
ended spanner. You can remove the tool by
continually turning the open-ended spanner.
Working with the milling motor
When you use a drill stand or a mill/drill unit (pos-
sibly with a milling table), you must refer to the
notes in the instructions for use provided there.
Also note that you must add the alignment fences
as far as possible on the milling cutter, the hand
deflector (screen) must be set down as tightly as
possible on the workpiece surface and, for milling
work, you must always use equipment that can
guarantee safe use of the tool, for example, align-
ment fence, auxiliary bearings, automatic feeders
or a non-return block for milling work.
The feed direction of the tool must always be the
opposite of the circulation direction of the milling
cutter (counter direction):
Operation
The tool runs on for a short time after
it is switched off.
If there is contact between the tool
and the support surface, there is a
danger of losing control of the
machine.
800FME / 1050FME 1050FME-1
1
10.000 min
-1
5.000 min
-1
2
12.600 min
-1
7.700 min
-1
3
17.000 min
-1
12.500 min
-1
4
21.000 min
-1
16.500 min
-1
5
25.000 min
-1
21.000 min
-1
6
29.000 min
-1
25.000 min
-1
Changing the tool
Disconnect the plug from the power
source before making any adjust-
ments, changing accessories, or stor-
ing power tools.
Such preventive safety measures
prevent accidental start of the power
tool.
Wear safety gloves for tool chang-
ing.
The tool insert can become very hot
after working for long periods and/or
the cutting edges of the tool insert
are sharp.
Attention! After you use the insertion
tool, perform a test run with an over-
speed and make sure that no-one is
within reach of the rotating insertion
tool. Damaged tools usually break in
this test period.
Operating tips
Wear protective glasses and hearing
protection.
Caution! Always mill in a counter
direction!
35664_BA_FME_0904.book Seite 18 Montag, 18. Mai 2009 10:09 10
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress 1050 FME at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress 1050 FME in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info