668580
23
Zoom out
Zoom in
Previous page
1/108
Next page
23
1: NUMBER (NUM:) .... [1...8] Select one of the preset crossfader curves.
2: POSITION ............. [0...127] Specify the position at which the
crossfader value will be at maximum.
3: CURVE ................ [-64...+63] Specify the shape of the crossfader curve.
MIDI control change message settings
3. CONTROL
Here you can make MIDI controller settings for when using push-knobs 1–
8 as MIDI controllers. From the setting main page, press the CONTROLS
button in the LCD display to access the CONTROLS page.
KNOB A–D
Specify the MIDI control messages that will be transmitted when you turn
push-knobs 1–8 as encoders.
1: NEXT .................................... Shows the next page.
2: NO. ......................... [0...127] Assigns a control change message to each
push-knob.
3: MIN ........................ [0...127] Specifies the minimum control change
value for each push-knob.
4: MAX ....................... [0...127] Specifies the maximum control change
value for each push-knob.
5: PREV .................................... Shows the previous page.
6: MIDI CH .................. [1...16] Specifies the MIDI channel for each push-
knob.
7: BEHAVIOR ...... [ABS, REL] Specifies the operation mode for each
push-knob.
ABS: The knob will operate in absolute value
mode.
REL: The knob will operate in relative value
(sign bit) mode.
Turning the knob toward the right (when
increasing) will transmit values of 1, 2, 3,
…, 64. Turning the knob toward the left
(when decreasing) will transmit values of
65, 66, 67…127.
Note: If you select “REL” (relative value mode), make sure that your
software supports this type of operation.
SW A–D
Here you can specify the MIDI control messages that will be transmitted
when you press push-knobs 1–8 as switches.
1: NEXT .................................... Shows the next page.
2: NO. ......................... [0...127] Assigns a control change message or note
number to each switch.
3: OFF VAL ................ [0...127] Specify the value of the control change that
will be transmitted when each switch is
turned off. If you've selected "NOTE" as
the type, this is fixed at note-off.
4: ON VAL ................. [0...127] Specify the value of the control change that
will be transmitted when each switch is
turned on. If you've selected "NOTE" as
the type, this specifies the note-on velocity
value.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg Zero 8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg Zero 8 in the language / languages: English, German, French as an attachment in your email.

The manual is 3,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info