707337

Korg microKORG XL Manual

84
Zoom out
Zoom in
Previous page
1/103
Next page
microKORG XL
84
Program change, Bank select
Program change [Cn, pp]
(n: channel, pp: program number)
When you switch programs, a program change message with a program
number for the corresponding program 1–128 (A11–B88) will be transmit-
ted.
If you want program changes to be transmitted and received, set the MIDI
FLT page “PROG CHG” to ENABLE. If this is set to DISABLE, program
change messages will not be transmitted or received.
Bank select MSB (CC#00) [Bn, 00, mm]
Bank select LSB (CC#32) [Bn, 20, bb]
(n: channel, mm: bank number upper bytes, bb: bank number lower bytes)
When you switch programs in Play mode, Bank Select and Program
Change messages are transmitted.
You can use Bank select and program change messages to switch the set-
tings of an individual timbre used by a program to the settings of another
timbre, one used by a different program. These messages are received on
the MIDI channel of the timbre selected by TIMBRE SELECT.
Pitch bend
Pitch bend change [En, bb, mm]
(n: channel, bb: lower digits of value, mm: upper digits of value)
When pitch bend change messages are received, a pitch bend will occur
according to the PITCH page “P.BEND” value. Pitch bend can also be used
in a Virtual Patch (PATCH1–PATCH6 page) for a synth program, as a mod-
ulation source for a vocoder program (VC FILT page), or as a control
source for a effect parameters. In this case, the message will act as a mod-
ulation source where mm=64, bb=00 will be 0 (center value) for the range
of –127 – +127. (This message is received on the timbre channel.)
When you move the [PITCH] wheel on the microKORG XL, pitch bend
change messages are transmitted on the Global MIDI channel.
If you want pitch bend changes to be transmitted and received, set the MIDI
FLT page “P.BEND” to ENABLE. If this is set to DISABLE, pitch bend
change messages will not be transmitted or received.
Control changes
Control changes [Bn, cc, vv]
(n: channel, cc: control change no., vv: value)
When you use knobs [1]–[3] to edit certain parameters, or when you oper-
ate certain buttons or the [MOD] wheel, the assigned control change will be
transmitted. Conversely, when control change numbers corresponding to
the knob [1]–[3] settings are received, the corresponding controller or
parameter will be controlled.
If you want control changes to be transmitted and received, set the MIDI
FLT page “CTRL CHG” to Enable. If this is set to Disable, control change
messages will not be transmitted or received.
NOTE
Use the CC MAP page to assign control change messages to parame-
ters.
• Modulation depth (CC#01) [Bn, 01, vv]
When a modulation depth message is received, the LFO2 vibrato depth will
change according to the value specified for PITCH “VIB INT.” If the value of
the received message is the maximum value (127), vibrato will be applied
over the full pitch range specified by “VIB INT.” If the value of the received
message is 0, no vibrato will apply.
When you move the microKORG XL’s [MOD] wheel, modulation depth
messages are transmitted on the Global MIDI channel.
• Volume (CC#07) [Bn, 07, vv]
If you assign the control change Volume (CC#07) to “LEVEL” in the CC
MAP page, incoming Volume messages will control the volume.
• Panpot (CC#10) [Bn, 0A, vv]
If you assign the control change Panpot (CC#10) to “PANPOT” in the CC
MAP page, incoming Panpot messages will control the stereo position of
the sound.
Bank (CC#00) MSB Bank (CC#32) LSB Program Change value Bank&Prog Number
00 00 000–127 (00–7F) A11–B88
Bank (CC#00) MSB Bank (CC#32) LSB Program Change value Timbre Number
32 32 000–127 (00–7F) A11–B88 Timbre 1
32 33 000–127 (00–7F) A11–B88 Timbre 2
… 84 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg microKORG XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg microKORG XL in the language / languages: English as an attachment in your email.

The manual is 8,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info