Manual Korg KingKorg (page 19 of 116) (English, German, French, Spanish)

707401

Zoom out

Zoom in

1/116

Editing the sound

3. Use the FX control knobs to adjust the parameter values.

3. Editing the vocoder

Selecting the vocoder for editing

The procedure for editing the vocoder is essentially the same as

when editing a timbre, but you’ll first need to turn the vocoder on

and select the vocoder as the target for editing.

The “v02:Voc.Carrier–v18:Voc.Amp” pages won’t appear

unless you’ve pressed the VOCODER button to turn on the

vocoder switch.

The parameters of the 16 band‐pass filters (analysis filter and

synthesis filter) and the envelope follower can be edited in the

PROGRAM “v09:Voc.Filter–v18:Voc.Amp” pages.

1. Select a synth program. (OM: p.13 “Selecting a program”)

2. Press the VOCODER button to make it light up.

The vocoder will turn on, and will be selected as the target for

editing.

3. Use the PAGE +/- buttons to access the vocoder parameter

editing pages.

TIP:

If you raise the direct level in the PROGRAM “v15:Voc.Amp”

page, the audio input will be output directly. Adjust this value

while checking the audio input.

TIP:

If you are unable to notice the eect, press the VOCODER

buon to make it light up, and then adjust the timbre A level in

the PROGRAM “v02:Voc.Carrier” page or the vocoder level in

the PROGRAM “v18:Voc.Amp” page.

Carrier (CARRIER)

The most suitable waveform for the carrier is a waveform that

contains a large number of overtones, such as a sawtooth wave

or a pulse wave with a fixed pulse width. These parameters can

be edited in the PROGRAM “v02–v03:Voc.Carrier” pages.

TIP:

To input a sawtooth wave to the carrier, edit timbre A

so that its PROGRAM “s13:OSC1” page Type seing is

“SAW,” and edit the vocoder seing in the PROGRAM

“v02:Voc.Carrier” page to specify the timbre A input level.

Modulator (MODULATOR)

A human voice is typically input as the modulator. On the

KingKORG, you can choose either the mic input (Input) or

timbre B (Timbre B) as the modulator. You can edit these

parameters in the PROGRAM “v04:Voc.Modultr” page.

4. Editing the arpeggiator

Selecting the timbre(s) to arpeggiate

For a program that uses two timbres, you can select the timbre(s)

that will be played by the arpeggiator.

In the PROGRAM “a05:Arp” page you can specify the timbre(s) that

will be sounded by the arpeggiator. You can make both timbres A/B

be arpeggiated, or arpeggiate just one timbre.

Tonal effects synchronized with the arpeggio

Synchronizing the LFO frequency or delay time to the

arpeggiator tempo

You can synchronize the frequency of LFO1 or LFO2 to the arpeggio

tempo. This lets you apply modulation that’s synchronized with the

tempo. This also gives you the ability to specify an effect’s delay

time as a multiple of the tempo so that the delay time will follow

even if you change the tempo of the arpeggio. You can also

synchronize the KingKORG’s arpeggiator to an external MIDI

sequencer, so that the LFO1/2 frequency or the delay time will be

controlled from your external sequencer.

Modifying the arpeggio

You can modify the arpeggio by turning each arpeggio step on/off.

This is called the “step arpeggiator” function.

Using the step arpeggiator to modify the arpeggio

1. Press the PROGRAM (GLOBAL) button to make it light.

2. Use the PAGE +/- buttons to access the PROGRAM “a12:Arp”

page.

3. Press the value dial.

The step setting screen will appear.

4. Use the PAGE +/- buttons to move the “ ” cursor, selecting

the step that you want to edit.

5. Turn the value dial to turn the step on or off.

In the main display, set the indication to “O” (on) for steps that

you want to enable. If you select “_” (off), the note for that step

will be a rest.

Repeat steps 4 and 5 to specify other steps.

6. Press the value dial to confirm the on/off settings of the steps.

TIP:

The number of available steps can be specied in the PRO‐

GRAM “a10: Arp” page. (PG: “3. Arpeggio parameters”)

5. Restoring an edited program value to

its original setting

When you set a value to the same value stored in the original preset

program or saved program, the ORIGINAL VALUE LED will light up.

After editing a value, you can restore that value to its original setting

by turning knob to the value that makes the ORIGINAL VALUE

LED light up.

If you want to discard all the edits you’ve been making, and recall

the content that’s stored in internal memory, simply select another

program without saving the current edits, and then recall the

desired program once again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Korg KingKorg in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 32,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Korg KingKorg Manual

Product: