707401

Korg KingKorg Manual

18
Zoom out
Zoom in
Previous page
1/116
Next page
18
KingKORG Owner’s manual
2. Editing two timbres
In each program, you can use two timbres: TIMBRE A and TIMBRE B.
TIP:
You can’t select TIMBRE B if the PROGRAM “p03: Common”
page Voice Mode parameter is set to “Single.” If “Layer” or
“Split” is selected, the TIMBRE A/B select buons will light to
indicate the timbre that you’re editing.
TIP:
The voice mode parameter in the PROGRAM “p03: Common”
page is common to the entire program.
Using two timbres (Layer)
When using two timbres, you have a choice of two modes that
determine how the timbres will work. In this example, we’ll set the
PROGRAM “p03: Common” page Voice Mode parameter to “Layer.”
When you set this parameter to “Layer,” the two timbres will be
heard simultaneously when you play the keyboard.
1. Use the PAGE +/- buttons to access the PROGRAM “p03
Common” page.
2. Turn the value dial to set the voice mode to “Layer.”
The TIMBRE A select button and the master effect timbre LEDs
will light up.
Selecting a timbre to edit
When editing a program that uses two timbres, you’ll need to select
a timbre to edit.
Use the TIMBRE A/B select buttons to select the timbre that you
want to edit. The timbre select button you selected will light up,
allowing you to edit that timbre.
Editing the filter and EG
On the KingKORG you can use the front panel knobs and buttons to
control the filter and EG in real time.
You can choose one of three ways in which the knobs will work
when you turn them. (PG: “5. GLOBAL parameters”)
FILTER
Cutoff (CUTOFF)
This adjusts the cutoff frequency of the filter. The brightness of
the sound will change. Turning the knob toward the left will
darken the sound; turning it toward the right will brighten the
sound.
Resonance (RESONANCE)
This adjusts the amount of resonance for the filter. Resonance
adds a distinctive tonal character.
EG (Envelope Generator)
Attack (ATTACK1, ATTACK2)
This adjusts the attack time of EG1 (filter EG) and EG2 (amp
EG). The attack specifies the time from note‐on (the moment you
press the key) until the attack level is reached. It changes the
way in which the EG1 and EG2 will start. Turning the knob
toward the left will shorten the attack time; turning it toward the
right will lengthen the attack time.
Decay (DECAY1, DECAY2)
This adjusts the decay time of EG1 (filter EG) and EG2 (amp EG). The
decay specifies the time from when the attack level is reached until the
sustain level is reached. Turning the knob toward the left will shorten
the decay time; turning it toward the right will lengthen the decay time.
Sustain (SUSTAIN1, SUSTAIN2)
This adjusts the sustain level of EG1 (filter EG) and EG2 (amp
EG). The sustain specifies the level that is reached after the decay
time has elapsed and is sustained as long as you hold down the
key. Turning the knob toward the left will lower the sustain level;
turning it toward the right will raise the sustain level.
Release (RELEASE1, RELEASE2)
This adjusts the release time of EG1 (filter EG) and EG2 (amp
EG). The release specifies the time from note‐off (the moment
you release the key) until the sound has decayed to silence. It
will vary the release time of EG1 and EG2. Turning the knob
toward the left will shorten the release time; turning it toward
the right will lengthen the release time.
0
Attack Level
Time
Note on
Note off
Level
1: Attack Time 3: Sustain Level
2: Decay Time 4: Release Time
1
3
4
2
EG2
Adjusting effect settings
The KingKORG provides master effects that let you apply a variety
of effects to the sound, such as distorting it, modulating it, or adding
reverberation. The master effects are applied to the overall sound of
the two timbres.
The master effects consist of three sections (PRE FX, MOD FX, REV/
DELAY), and you can choose one type of effect for each section.
For example you might choose “EP.AMP” for the PRE FX section,
“TREMOLO” for the MOD FX section, and “HALL” for the REV/
DELAY section. For each section, you can also specify the timbre(s)
where that effect will apply.
1. Press an FX type select dial to select the timbre(s) where that
effect will apply.
The selected timbre LED(s) will light up. If both timbre LEDs A
and B are unlit, that effect will not be applied.
The timbre LED B will not light if the program’s voice
mode is “Single.”
2. Select an effect.
The LED of the selected effect will light.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg KingKorg at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg KingKorg in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 32,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info