683161
110
Zoom out
Zoom in
Previous page
1/196
Next page
Selecting a Frequency Characteristic for the TX
Equalizer
This transceiver comes with 6 types of frequency characteristics
for the TX equalizer. In addition, there are 3 other types that can
be customized according to the user’s preferences. A selection
can be made from these options.
1
Press and hold F [TX EQ] to display the TX Equalizer
screen.
.
2
Press F2 [ ]/ F3 [ ] or turn the [MULTI/
CH] control to select a characteristic.
Make a selection based on the equalizer effects in the table
below.
Effects
Purpose
High Boost 1 (HB1)
Boosts the high frequency component. This is
effective for audio sound that contains a low
frequency component.
High Boost 2 (HB2)
Boosts the high frequency component. The low
frequency attenuation level for this option is half
of that of the HB1 option.
Formant Pass (FP)
This option attenuates frequency components
that is outside the audio bandwidth so that the
audio can be heard more clearly.
Bass Boost 1 (BB1)
Boosts the low frequency component. This is
effective for audio sound that contains a high
frequency component.
Bass Boost 2 (BB2)
Boosts the low frequency component. The low
frequency is further boosted compared to BB1.
Conventional (C)
Applies a 3 dB boost to the frequency range of
600 Hz or higher. This is suited for
communication that attenuates gradually as it
approaches the low frequency range.
User 1 (U1) Frequency characteristics can be adjusted
according to the user’ preferences and stored in
the options between User 1 and User 3. The flat
frequency characteristic is selected in the
default setting.
User 2 (U2)
User 3 (U3)
3
Press and hold F [TX EQ] or press [ESC] to end the
process.
.
TX Characteristic Curve
Frequency (Hz)
OFF
HB1
HB2
FP
BB1
BB2
C
0
5
-5
-10
-30
-25
-20
-15
10
10
0
10
3
10
2
10
1
Adjusting the TX Equalizer
The frequency characteristics of the TX equalizer can be adjusted
to produce the desired sound quality.
1
Press and hold F [TX EQ] to display the TX Equalizer
screen.
2
Press F2 [ ]/ F3 [ ] or turn the [MULTI/CH]
control to select a characteristic.
3
Press F3 [ADJ] to display the TX Equalizer
Adjustment screen.
.
4
Press F3 [ ]/ F4 [ ] to select the frequency
band to adjust.
5
Press F5 [–]/ F6 [+] or turn the [MULTI/CH] control
to adjust the level of each frequency band.
Touching a point on the RX Equalizer Adjustment screen
selects the corresponding band and changes the frequency
to the selected level.
An alternative way is to touch a rough point followed by fine-
tuning in steps 3 and 4.
Pressing and holding F2 [(RESET)] resets all the frequency
levels to the default setting.
6
Press and hold F [TX EQ] or press [ESC] to end the
process.
Copying the TX Equalizer Settings
Equalizer effects that are configured according to the user’s
preferences can be copied and saved as user-defined settings.
1
Press and hold F [TX EQ] to display the TX Equalizer
screen.
2
Press F2 [ ]/ F3 [ ] or turn the [MULTI/CH]
control to select a characteristic.
.
3
Press F5 [COPY].
A message with instructions on how to specify the destination
for saving the settings is displayed.
.
8 TRANSMIT FUNCTIONS
8-6
110


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info