683161
74
Zoom out
Zoom in
Previous page
1/196
Next page
FFT Scope
The audio FFT scope is used for viewing the tuning status.
The two vertical lines on the left and right represent the mark and
space frequencies respectively. Adjust the tuning frequency while
receiving a signal such that the two peaks overlap evenly with the
two lines.
Waterfall
The waterfall is a time-series display of the RX signal spectrum
which functions in tandem with the FFT scope. The entire waterfall
display can also be shifted in tandem with changes in the RX
frequency.
X-Y Scope
The X-Y scope displays the tuning status in the RTTY (FSK) mode
as a cross pattern. The cross patterns bisect at right angles (90
degrees) when this transceiver is correctly tuned to the signal.
Threshold Level
Displays the threshold value of the RX signal level for decoding.
Operating the RTTY Encode/Decode Screen
The following operations are enabled when the RTTY
communication screen opens.
Pressing the [Page Up] or [Page Down] key scrolls the display
of the TX or RX details.
Key Behavior
F1 [MORE] Switches the key guide.
F3 [PAUSE]
Pauses update (drawing) of the TX/RX details
display area. Pressing the key again resumes the
update (drawing).
F4 [LOG]
Turns ON/OFF the communication log function.
Pressing and holding this key displays the screen
for selecting a log file that is saved.
F4 [(CLEAR)]
Pressing and holding the key clears the text
displayed on the TX/RX details screen.
F5 [THLD]
Switches to the threshold level configuration
mode.
F5 [MEMORY] Switches to the RTTY Message screen.
F6 [X-Y LEV]
Switches between the speed and density of the X-
Y scope.
F7 [EXTEND]
Enlarges the size of the RTTY communication
screen.
Pressing it again restores the screen to the
standard size.
Indicator Displays
Display
Behavior
.
Appears when the communication log function is
ON.
.
Appears when the communication log function is
ON and in the standby mode.
.
Appears when signal decoding is in progress.
.
Appears when encoding the characters in the TX
buffer.
.
Appears when the decode function is stopped or
disabled.
.
Appears when transmitting the message memory.
.
Appears when in the insert mode.
.
Appears when in the overwrite mode.
Saving RTTY Communication Logs
The CW, RTTY and PSK communication screens can be saved
using the communication log function. Please refer to
“Communication Log” on page 5-27.
Adjusting the RTTY Decode Threshold Level
Noise that occurs when there is no signal may sometimes be
erroneously detected as text, which results in the display of
unwanted text. To reduce the occurrence of such issues, adjust
the threshold level.
Raise the threshold level when there is frequent erroneous
detection due to noise.
1 Press F5 [THLD].
The threshold level setting can now be adjusted.
.
2 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to adjust the level.
Setting Value 1 to 10 (default) to 30 (1 step)
Adjust the threshold value in the ascending order according
to the receiving status of noise, for example. Start from a
small value between the range of 1 to 30 and configure the
threshold value to a point where reception is good.
To restore the default setting, press and hold F2 [(RESET)].
3
Press F1 [ ] to end the process.
FFT Scope/X-Y Scope Display Setting
The tuning scope displayed on the RTTY communication screen
can be switched to an “FFT scope” or “X-Y scope” display.
Configure in Menu [2-09]
RTTY Tuning Scope
Setting Value FFT Scope (default)/ X-Y Scope
The display toggles between the “FFT Scope” and “X-Y Scope”
each time the scope display on the screen is touched.
FFT Scope Waveform Averaging
The waveform displayed on the FFT scope can be averaged.
Averaging of the waveform reduces random noise and makes
observation of the target signal easier.
Configure in Menu [2-00]
FFT Scope Averaging
(RTTY Decode)
Setting Value
0 (default) to 9 (1 step) (minimum to maximum
averaging)
5 COMMUNICATING AIDS
5-18
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info