683161
54
Zoom out
Zoom in
Previous page
1/196
Next page
FM Mode S-meter Sensitivity
The default deflection type in the FM mode is the same as that in
the other modes. Selecting “High” switches the transceiver to the
same deflection type (high sensitivity) as our conventional models.
Configure in Menu [0-07] FM Mode S-Meter
Sensitivity
Setting Value Normal (default)/ High
This function is available when Menu [0-11] S-Meter
Scale is configured to “Type 1”.
Analog Meter Response
Configure the response speed of the analog meter indicator.
Configure in Menu [0-08] Meter Response Speed
(Analog)
Setting Value 1 to 3 (default) to 4 (1 step)
Meter with Peak Hold
Display the peak hold of the digital meter.
Configure in Menu [0-10] Meter Display Peak Hold
Setting Value Off/ On (default)
S Meter Scale
Switch the type of deflection for the S meter.
Configure in Menu [0-11]
S-Meter Scale
Setting Value Type 1 (default)/ Type 2
Type 1: Same scale as our HF products.
Type 2: Initial deflection is more sensitive compared to Type 1.
Additional notes for “Type 2”
The S meter indicator will appear deflected at all times
when there is external noise.
The movement may not be smooth as it is a pseudo
representation of the S meter deflection.
Narrowing the RF gain may disrupt the continuity from
S0 to S4.
TX Meter (Digital)
In addition to the analog meter display, a two-tiered digital meter
can also be displayed at the same time.
.
Configure in Menu [0-12] TX Digital Meter
Setting Value Off (default)/ On
The TX meter (digital) only appears in the analog meter
display mode.
The TX meter (digital) is displayed in a two-tiered bar format.
ALC is shown at the upper level, while the display at the lower
level varies according to the setting of the F [METER] digital
meter.
During transmission, the analog meter always displays the
TX output power.
Switching the Antenna
Switch the antenna that is connected to the antenna connector.
The ANT 1/2, RX ANT and DRV settings are automatically stored
in the antenna band memory. When the same band is selected
subsequently, the same antenna will be selected automatically.
Press and hold F [ANT/PRE].
Pressing and holding F [ANT/PRE] switches the option
between “ANT 1” and “ANT 2”.
When “ANT 1” is selected, <<
>> is displayed. When
“ANT 2” is selected, <<
>> is displayed.
Selectable Antenna Frequency Range (MHz)
0.03 to 0.522 10.5 to 14.5
0.522 to 2.5 14.5 to 18.5
2.5 to 4.1 18.5 to 21.5
4.1 to 6.9 21.5 to 25.5
6.9 to 7.5 25.5 to 30.0
7.5 to 10.5 30.0 to 60.0
60.0 to 74.8 (E type)
RX Antenna
Select an RX antenna.
To use an RX antenna such as an HF low-band Beverage antenna
or a directional loop antenna, connect it to the RX IN terminal on
the rear panel. The input impedance is 50 Ω. A self-made or
commercially available BPF or trap filter can also be inserted
between the RX IN and RX OUT terminals.
Press [RX ANT].
Pressing [RX ANT] each time enables or disables the RX
antenna of the selected band.
When the RX antenna is enabled, << >> is displayed on the
screen.
4 BASIC OPERATIONS
4-10
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info