683161
56
Zoom out
Zoom in
Previous page
1/196
Next page
Preset
The tuning results can be stored as preset information in the built-
in antenna tuner according to the preset frequency categories.
When the built-in antenna tuner is ON, the preset information that
corresponds to the current TX frequency is automatically
configured for the built-in antenna tuner.
Press [AT].
<< >> appears on the screen. When the antenna
tuner is ON while receiving, <<
>> is displayed. The
preset information that corresponds to the current TX
frequency is configured for the built-in antenna tuner.
When the TX frequency is altered, the preset information that
corresponds to the preset frequency category is
automatically configured for the built-in antenna tuner.
To turn off the built-in antenna tuner, press [AT] again.
Preset Frequency Categories for Built-in Antenna Tuner (MHz)
0.030 f < 1.850 14.100 f < 14.500
1.850 f < 2.500 14.500 f < 18.500
2.500 f < 3.525 18.500 f < 21.150
3.525 f < 3.575 21.150 f < 21.500
3.575 f < 3.725 21.500 f < 25.500
3.725 f < 4.100 25.500 f < 28.300
4.100 f < 6.900 28.300 f < 29.000
6.900 f < 7.050 29.000 f < 30.000
7.050 f < 7.100 30.000 f < 51.000
7.100 f < 7.500 51.000 f < 52.000
7.500 f < 10.500 52.000 f < 53.000
10.500 f < 14.100 53.000 f < 60.000
60.000 f < 74.800 (E type)
Holding Transmission at the End of Antenna Tuning
Transmission can be held after antenna tuning has ended.
Configure in Advanced Menu [7]
TX Hold After
Antenna Tuning
Setting Value Off (default)/ On
Off: Returns to receiving state after antenna tuning has ended.
On: Continues 10 [W] transmission in the CW mode after
antenna tuning has ended.
When transmission is held after antenna tuning has
ended, the held status will be canceled when
transmission operations such as [SEND] or PF [DATA
SEND] is performed or when [AT] is pressed.
Switching Antenna Tuner Behavior during Reception
Signals received may be made to pass through the built-in antenna
tuner. Turning ON this function may help to reduce reception
interference from other distant frequencies.
Configure in Advanced Menu [8] Antenna Tuner
during RX
Setting Value Off (default)/ On
Off: Signals received do not pass through the built-in antenna
tuner.
On: Signals received pass through the built-in antenna tuner.
When full break-in is ON in the CW mode, the antenna
tuner will function during reception regardless of the
above setting.
If the TX and RX frequencies are different during split
operation, the antenna tuner will not function during
reception regardless of the above setting.
Configuring the Built-in Antenna Tuner Behavior for
Each Band
Two options to either store the ON/OFF status of the built-in
antenna tuner separately for each band category or to store the
same status for all bands are available.
Configure in Advanced Menu [9]
Antenna Tuner
Operation per Band
Setting Value Off (default)/ On
Off: Stores the same ON/OFF status of the built-in antenna
tuner for all bands.
On: Stores the ON/OFF status of the built-in antenna tuner for
each band category.
Connecting the External Antenna Tuner AT-300
To use the external antenna tuner AT-300, connect it to the ANT
1 connector and AT connector.
AT-300 will not function if it is connected to the ANT 2 connector.
AT connector is a control terminal that is used exclusively for
AT-300. It cannot be used to control other external antenna
tuners. When an external antenna tuner other than AT-300 is
connected, make use of TX tuning.
AT-300 cannot be used with the 50/70 MHz band. When
using a 50/70 MHz band antenna, connect it to the ANT
2 connector.
When AT-300 is connected to the AT connector and ANT
1 is used, the signal bypasses the built-in antenna tuner
circuit.
Production of the AT-300 has been discontinued.
.
AT-300
ANT 1
Connector
TS-890S
4 BASIC OPERATIONS
4-12
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info