683161
53
Zoom out
Zoom in
Previous page
1/196
Next page
TX Output Power Limiter
The TX output power limiter can be used to limit the TX output
power. This is a function to prevent the TX output power level from
exceeding the preconfigured level for each band when the
[POWER] control is turned. It can also be used to limit TX output
power only in the DATA mode with a specific band.
Turning ON/OFF TX Output Power Limiter
Press F [MAX-Po].
Pressing F [MAX-Po] each time toggles the TX output power
limiter function between ON and OFF.
When the TX output power limiter is turned ON, pressing F
[MAX-Po] displays the confirmation screen for turning off the
TX output power limiter.
Pressing [F4](OK) turns off the TX output power limiter
function. Pressing [F7](CANCEL) or [ESC] cancels the
operation.
.
Configuring the TX Output Power Limiter
1 Press and hold F [MAX-Po] to display the TX output
power limiter screen.
.
2
Press F4 [ ]/ F5 [ ] to select a frequency band.
3
Press F2 [ ]/ F3 [ ] to select the TX output
power to limit.
Select the TX output power item to limit as follows.
Max Power Limit: For configuring the TX output power limit
during transmission.
The TX output power limit can be configured separately for
the SSB, CW, FSK/PSK, FM/AM and DATA modes.
TX Tune Power: For configuring the TX output power limit
during TX tuning.
4 Press F6 [–] / F7 [+] or turn the [MULTI/CH] control
to select a limit value for TX output power.
To restore the default setting, press and hold F1
[(RESET)].
5 Press and hold F [MAX-Po] or press [ESC] to end
the process.
A different TX output power limit cannot be configured
for the antenna connectors (antenna 1/2).
If Advanced Menu [6] TX Power Down with Transverter
Enabled is configured to “On”, the F [MAX-Po] and watt
display at the right edge of the screen will disappear
when the transverter or drive output is turned ON.
Meter
The meter displays the measured reading of the S meter during
reception and that of the selected meter during transmission.
Changing the Meter Type
A digital meter and two types of analog meters are available for
selection.
Changing the Meter Type from the Menu
Configure in Menu [0-09] Meter Display Pattern
Setting Value Digital/ Analog (White) (default)/ Analog (Black)
Changing the Meter Type via Touchscreen Operation
Touch the meter display area while an analog or
digital meter is displayed
Touching the screen each time switches the meter in the
following sequence: “Digital” → “Analog (White)” → “Analog
(Black)”.
When in the compressed mode, touching the meter will not
change the display.
.
Analog MeterDigital Meter
Switching between TX Meters
Press F [METER].
Press F [METER] each time switches the display as follows
according to the meter type.
Analog meter display when the TX meter (digital) is OFF:
“Po” → “SWR” → “Id” → “COMP”* → “ALC” → “Vd” →…
Display at the bottom of the TX meter (digital) when the
TX meter (digital) is ON:
“SWR” → “Id” → “COMP”* → “Vd” → “TEMP” →…
The last line of the display in the digital meter display
mode:
“SWR” → “Id” → “COMP”* → “Vd” → “TEMP” →…
When a mini digital meter is displayed:
“Po” “SWR” “Id” “COMP”* “ALC” “Vd” “TEMP” →…
Po
Indicates the TX output power. (Output power at the
peak)
SWR
Indicates the standing wave ratio which reflects the
matching status of the antenna.
COMP
Indicates the amount of TX audio amplitude that is
compressed by the speech processor.
ALC Indicates the ALC level.
ld Indicates the drain current of the final FET.
Vd Indicates the voltage of the final FET.
TEMP Indicates the temperature of the internal circuit.
An external meter can also be used to display the signal
level by connecting an analog meter to the METER
terminal on the rear panel.
*: COMP meter can only be selected when the speech
processor is ON.
BASIC OPERATIONS 4
4-9
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info