606692
40
Zoom out
Zoom in
Previous page
1/96
Next page
32
7 COMMUNICATING AIDS
Data VOX Delay Time
Select an appropriate delay time for after the audio
signal input to the ACC2 or USB connector ends.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
turn the MULTI/CH control to select Menu No. 77.
2 Press [M.IN]/ [SCAN (SG.SEL)] to set your
desired delay time.
3 Press [MENU] to exit Menu mode.
USB/ ACC2 VOX Gain
When using the ACC2 or USB connector for VOX
transmission, take the time to properly adjust the
VOX gain.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR]
or turn the MULTI/CH control to select Menu
No. 78 (USB connector) or Menu No. 79 (ACC2
connector).
2 While sending an audio signal to the ACC2 or
USB connector, adjust the value (default is 4)
using [M.IN]/ [SCAN (SG.SEL)] until the
transceiver reliably switches to transmit mode
each time you send an audio signal to the
connector.
3 Press [MENU] to exit Menu mode.
SPEECH PROCESSOR
The Speech Processor levels out large fl uctuations in
your voice while you speak. When using SSB, AM, or
FM mode, this leveling action effectively raises
the average TX power (SSB/AM) or raises the
deviation to an adequate level (FM), resulting in a
more understandable signal. The amount of voice
compression is fully adjustable. Using the Speech
Processor makes it easier to be heard by distant
stations.
Level
Level
Time
Time
Speech
Processor
ON
Speech
Processor
OFF
1 Select USB, LSB, AM, or FM mode.
2 Press [PROC (LEV)] to turn the Speech Processor
ON.
• “
appears.
3 Press and hold [PROC (LEV)] to enter the Speech
Processor input level adjustment mode.
4 As you speak into the microphone, turn the
MULTI/CH control so that the compression meter
indicates that the compression level is around
10 dB while you speak.
Using higher compression will not improve
your signal clarity or apparent signal strength.
Excessively compressed signals are more
diffi cult to understand due to distortion and are
less pleasant to hear than signals with less
compression.
5 Press and hold [PROC (LEV)] to exit the Speech
Processor input level adjustment mode.
6 Press [MIC (CAR)] to enter the Speech Processor
output level adjustment mode.
As you speak into the microphone, turn the
MULTI/CH control so that the ALC meter
refl ects according to your voice level, but does
not exceed the ALC limit. Press [MIC (CAR)] to
exit when you fi nish the adjustment.
Note: The Speech Processor ON/OFF are stored in each of the
following modes.
SSB/ SSB-DATA/ CW/ FSK / FM/FM-DATA/ AM/ AM–DATA
Speech Processor Effect
When using the Speech Processor, you can
change its effect.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
turn the MULTI/CH control to select Menu No.
35.
2 Press [M.IN]/ [SCAN (SG.SEL)] to set the
Processor Effect to SOFT or HARD (default).
3 Press [MENU] to exit Menu mode.
XIT (TRANSMIT INCREMENTAL TUNING)
Similar to RIT, XIT provides the ability to change your
transmission frequency by ±9.99 kHz in steps of
10 Hz without changing your reception frequency. If
the Fine Tuning function is ON, the frequency step
size becomes 1 Hz (±9.999 kHz).
1 Press [XIT].
• “
and the XIT offset appear.
2 If required, press [CL] to reset the XIT offset to 0.
3 Turn the RIT/ XIT control to change your transmit
frequency.
4 To turn XIT OFF, press [XIT].
• “ and the offset frequency disappear. The
transmission frequency is returned to the
frequency that was selected prior to step 1.
Note:
The frequency shift set by the XIT control is also used by the
RIT function. Therefore, changing or clearing the XIT offset
also affects the RIT offset.
When the XIT frequency goes beyond the available
transmission frequency, the transceiver automatically stops
transmitting.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-590SG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-590SG in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-590SG

Kenwood TS-590SG User Manual - German - 96 pages

Kenwood TS-590SG User Manual - Dutch - 96 pages

Kenwood TS-590SG User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info