45743
89
Zoom out
Zoom in
Previous page
1/150
Next page
81
15 OPERATOR CONVENIENCES
COMPUTER CONTROL
By connecting this transceiver to a computer, you can
change the computer into an electronic console from
which you can remotely control functions of the
transceiver. This capability makes remote operation
of your transceiver possible from across the room,
from another room, or when coupled with other
commercially available products and where lawful,
from another city, state, or country via a telephone
connection.
Note:
You can use the front panel controls while using computer
control. Settings done from the front panel are effective
immediately.
After the computer is disconnected or turned off, all values and
settings on the front panel are restored.
SETTING UP
Equipment Needed
A PC equipped with an RS-232C serial port.
One straight cable. This cable must have a 9-pin
D-Sub RS-232C female connector at one end, and
at the other end a 9-pin or a 25-pin D-Sub
RS-232C female connector that mates with the
RS-232C port of your computer.
Transceiver control application.
To design your programs, consult “APPENDIX” for the
necessary information.
Connections
Connecting the transceiver to the computer is easy.
See the diagram given in “CONNECTING
PERIPHERAL EQUIPMENT” {page 93}.
Note: Before connecting this transceiver to the computer, switch
OFF the power to both the transceiver and the computer.
COMMUNICATION PARAMETERS
In order to control the transceiver by computer, you
must first choose the communication parameters.
1 On the computer, configure your transceiver
control application for 8 data bits, 1 stop bit and
no parity.
2 On the transceiver, select the same transfer rate
and number of stop bits via Menu No. 56.
The defaults are 9600 bps and 1 stop bit.
Note: To reliably use the 38400 or 57600 bps transfer rates, the
RS-232C port of the computer must support these high-speed
communications parameters.
REMOTE MICROPHONE CONTROLLER
If you have a DTMF microphone, you can use the
microphone as a wired remote control unit as
described below.
1 Plug the DTMF microphone into the microphone
connector of the transceiver.
2 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 45D.
3 Press [+] to select ON.
4 Press [MENU] to store the setting and exit Menu
mode.
The DTMF keys function as follows:
FMTD
yek
noitcnuF
CNUF
edom
FMTD
yek
noitcnuF
CNUF
edom
1nacS–9
hcleuqS
1
nwoD/pU
2
/enoT
/SSCTC
SCD
edoC
tceleS
0
RWP
1
nwoD/pU
3VERTFIHSATNE–
4zHM–BLRTC
/NIAM
BUS
5INOM
KCOL
NO
2
CretaepeR–
61ecioV
KCOL
FFO
2
DCNUF
CNUF
FFO
7emuloV
1
–nwoDnwoD
8dnaB
1
–# pUpU
1
Use the [#] (Up) and [ ](Down) keys to change the settings of
these functions.
2
The LOCK function is for the microphone keypad.
Note:
Microphone Remote does not function while transmitting.
You can use the DTMF Memory function {page 75} with the
Microphone Remote function.
The Repeater function is available for K-type models only.
Normally, pressing [2] cycles through Tone, CTCSS, DCS, and
OFF. However, if 1750 Hz is selected for Tone, pressing [2] will
only transmit the 1750 Hz tone. To return to Tone/ CTCSS/ DCS
mode, you must first deselect 1750 Hz for Tone.
Press [D] to enter FUNC mode, to use the 2nd function of the
DTMF keys. Pressing [D] while in FUNC mode will exit FUNC
mode.
[FUNC] on the transceiver works independently from the
Microphone Remote [FUNC] key.
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info