45743
90
Zoom out
Zoom in
Previous page
1/150
Next page
82
15 OPERATOR CONVENIENCES
WIRELESS REMOTE CONTROL
(K-type ONLY)
If you have a Kenwood TH-D7A handheld transceiver,
you can use it to remotely control the 144 MHz and
440 MHz bands of the TS-2000(X) transceiver, using
FM mode. You will be controlling one band on the
TS-2000(X) transceiver while sending DTMF tones to
the other band from the remote control transceiver.
This function is useful, for example, when you want to
control the VHF/ UHF FM repeater function of the
TS-2000(X) transceiver from a location outside your
home or vehicle.
Note:
To remotely control the TS-2000(X), you can also use a handheld
transceiver which does not have a remote control function, but a
DTMF function. You must, however, manually send DTMF tones
for control code strings. Skip steps 1 and 3 in “PREPARATION”,
below.
FCC rules permit you to send control codes only on the 440 MHz
band.
PREPARATION
Assuming that the 144 MHz band of the TS-2000
transceiver will be controlled.
On the control transceiver:
1 Program a 3-digit secret number.
If you are using a TH-D7A, see “WIRELESS
REMOTE CONTROL” in its instruction manual.
2 Select the transmit frequency on the 440 MHz
band.
3 Enter the Remote Control mode.
On the TS-2000 transceiver:
4 Access Menu 61C, and select the same secret
number that you selected in step 1.
5 Select the receive frequency on the 440 MHz
band of the sub-receiver.
Mate this frequency with the transmit frequency
on the control transceiver.
6 Select the 144 MHz band as the TX band or
Control band for the main transceiver.
7 To have the TS-2000(X) transceiver send a control
acknowledgment to the handheld, access Menu
61D and select “ON”.
DTMF tones which represent the secret
number will be used as an acknowledgment.
8 Access Menu 61E and select “ON”.
•“ ” appears when the TS-2000(X) enters
Remote Control mode.
CONTROL OPERATION
When in Remote Control mode, the DTMF keys of the
control transceiver will function as shown in the table
below. Each time you press the desired key, the
transceiver will automatically enter transmit mode and
send the corresponding command to the mobile.
Note: If you are using a transceiver without a remote control
function, manually send “AXXX#YA#” where “XXX” is your 3-digit
secret number and “Y” is a single-digit control command. If you do
not add ”A#” on the end, you can skip sending “AXXX#” next time;
however, the mobile may be accidentally controlled by other stations.
1NOSCD 9RM
2NOENOT 0WOL
3NOSSCTC ARETNE
4FFOSCD BLESENOT
5FFOENOT CNORETAEPER
6FFOSSCTC DFFORETAEPER
7LLAC NWOD
8OFV #PU
To change the transmit/ receive frequency:
([VFO] [ENTER] [0] ~ [9] (enter the necessary
digits) [ENTER]) or ([VFO] [UP]/ [DOWN])
To recall a memory channel:
([MR] [ENTER] [0] ~ [9] (enter the necessary
digits) [ENTER]) or ([MR] [UP]/ [DOWN])
To change the tone (or CTCSS) frequency:
([TONE SEL] [0] ~ [9] (enter 2 digits; ex. [0], [5])
[TONE SEL])
Use Nos. 01 to 38 shown in the table on page 35.
First activate the Tone or CTCSS function. You
can select a separate tone frequency for the Tone
and CTCSS functions.
Note: While in Wireless Remote Control mode, you can perform only
the following operations on the TS-2000(X) transceiver.
Transmit
Acknowledge ON/ OFF
Secret Number Change
Partial/ Full Reset
90


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info