45743
87
Zoom out
Zoom in
Previous page
1/150
Next page
79
15 OPERATOR CONVENIENCES
TNC
This transceiver has a built-in TNC that is usually
used for the Packet Cluster Tune {page 53} or
SkyCommand II+ operations {page 83}. However,
you can also utilize the built-in TNC as a high
(9600 bps) or normal (1200 bps) speed TNC. The
TNC can be controlled by an external PC that is
connected to COM port on the rear panel {page 49}.
Available TNC command set is listed in the Appendix.
If you desire, you can connect an external TNC or
proprietary TNC/ MCP to ACC2 connector. To
interface an external TNC/ MCP with the TS-2000(X),
refer to the ACC2 connector information {page 95}
and accessing Menu Nos. 50B ~ 50F then configure
and adjust the Menu parameters to work with the
external TNC/ MCP.
Note: You do not have to disable the built-in TNC to interface with an
external TNC. Both the main transceiver and sub-receiver can work
independently unless the transceiver is transmitting on the same
band.
TRANSVERTER
If you have a transverter that converts the TS-2000
operating frequencies to other frequencies, you can
use this TS-2000 transceiver as a transverter exciter.
Consult the instruction manual that came with the
transverter for interfacing to the TS-2000.
1 Connect the transverter to the ANT 1, ANT 2,
ANT 144, ANT 430, or ANT 1.2G (TS-2000
optional) connector on the rear of the transceiver.
2 Select the exciter operating frequency on the main
transceiver of the TS-2000(X).
The transverter will use this frequency as the
reference for converting frequencies.
3 Access Menu No. 25, and select ON by pressing
[+].
The output power is automatically set to the
lowest power for that frequency. See TX
POWER (below).
4 Press [MENU] to store the setting and exit the
Menu mode.
5 Press [ENT], then set the target converting
frequency, using the numeric keys.
6 Press [ENT] to complete the entry.
7 The transceiver displays the target transverter
frequency instead of the actual operating
frequency.
Note: When using a transverter, not all the functions of this
transceiver are available.
TX MONITOR
TX monitor allows you to monitor the on-going
transmission sound. This is convenient when you
want to check the modulation sound quality of the
transmission. In FSK mode, you can monitor the FSK
signal that the TS-2000(X) is transmitting.
1 Press [FUNC], [PWR/ TX MONI].
2 The current TX monitor setting appears.
3 Turn the MULTI/ CH control to select the monitor
sound level from OFF, and 1 to 9.
4 Press [CLR] to store the selected TX monitor
level.
Note:
We recommend you use headphones when you monitor SSB,
AM, or FM mode, in order to avoid howling.
The CW transmission signal cannot be monitored using the TX
monitor function. Use the CW sidetone function to monitor CW
transmissions (Menu Nos. 13 and 31).
TX POWER
You can adjust the transmission output power by
pressing [PWR/ TX MONI] and turning MULTI/ CH
control. If more precise power adjustment is
required, access Menu No. 23 and select ON. When
this menu is ON, the power adjustment steps change
as shown in the table below.
dnaB edoM
32.oNuneM
FFO
32.oNuneM
NO
/zHM05/FH
zHM441
/WC/BSS
KSF/MF
W001~5
5fospetsni
W001~5
1fospetsni
MA
W52~5
5fospetsni
W52~5
1fospetsni
044/034
zHM
/WC/BSS
KSF/MF
W05~5
5fospetsni
W05~5
1fospetsni
MA
W5.21~5
1fospetsni
zHG2.1
/WC/BSS
KSF/MF
W01~1
1fospetsni
MA
W5.2~1
1fospetsni
Note:
The output power settings are stored independently for HF, 50 MHz,
144 MHz, 430/ 440 MHz and 1.2 GHz (TS-2000/ TS-B2000
optional). As shown in the table above, you can also store different
output power settings for AM and other modes for each operating
band.
For AM mode in the 430/ 440 MHz band and the 1.2 GHz (TS-
2000/ TS-B2000 optional) band, the final step is 0.5 W, rather
than 1 W.
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info