45743

Kenwood TS-2000E Manual

86
Zoom out
Zoom in
Previous page
1/150
Next page
78
15 OPERATOR CONVENIENCES
If you want to reverse the output:
1 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 17.
2 Press [+] to select ON.
3 Press [MENU] to store the setting and exit Menu
mode.
The output is now reversed.
Note: If you are using headphones, the transceiver mutes. The left
channel represents the internal SP or EXT.SP1 and the right channel
represents the EXT.SP2.
S-METER SQUELCH
The S-meter Squelch function opens the squelch only
when the receiving signal has the same or greater
strength than the S-meter Squelch setting. This
function helps you to not open the squelch when
receiving weak signals that you do not want to hear.
1 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 19A.
2 Press [+] to select ON.
3 Turn the MAIN SQL control and/or the SUB SQL
control to adjust the S-meter Squelch threshold
level. When you turn SQL control, the indicators
on the S-meter move accordingly.
4 Press [MENU] to store the settings and exit Menu
mode.
Note: The squelch threshold level of the S-meter squelch is
around the 9 o’clock position for FM (both MAIN and SUB SQL),
the 11 o’clock position for other modes (MAIN SQL), and the 9
o’clock position for AM (SUB SQL), regardless of the SQL controls
position.
SQUELCH HANG TIME
You can adjust the squelch hang time to continuously
monitor unstable signals. When the signal is
temporarily weaker than the S-meter Squelch
threshold level, the squelch does not mute the signal
for a short period of time. In this way, you can
continuously monitor the unstable signal.
1 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 19B.
2 Press [+]/ [–] to select OFF, 125 ms, 250 ms, or
500 ms.
3 Press [MENU] to store the settings and exit Menu
mode.
TIME-OUT TIMER
The Time-out Timer limits the time of each
transmission. It is also useful to prevent a long
accidental transmission.
1 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 24.
2 Press [+]/ [–] to select OFF, 3 minutes, 5 minutes,
10 minutes, 20 minutes, or 30 minutes.
3 Press [MENU] to store the settings and exit Menu
mode.
RX DSP EQUALIZER
EQUALIZING RECEIVING AUDIO (SSB/ FM/ AM)
Use Menu No. 20 to change the receiver frequency
responses of the target signal. You can select one
from six different receiver profiles including the
default flat response. Selecting any of the following
items from the Menu causes “ ” to appear on
the display.
• Off (OFF):
The default frequency response for SSB, FM, and
AM.
• High boost (H BOOST):
Emphasizes higher audio frequencies; effective for
a bassy voice.
• Formant pass (F PASS):
Improves clarity by suppressing audio frequencies
outside the normal voice frequency range.
• Bass boost (B BOOST):
Emphasizes lower audio frequencies; effective for
a voice with more high frequency components.
• Conventional (CONVEN):
Emphasizes by 3 dB frequencies at 600 Hz and
higher.
• User (USER):
Reserved for the ARCP software. Off is
programmed at the factory as a default.
SEPERATE SPEAKER OUTPUT
The TS-2000(X) has 2 independent receivers and is
capable of receiving 2 different frequencies at the
same time. If no external speaker is connected to the
TS-2000(X), both audio signals are mixed internally,
then output through the internal speaker.
1 Connect the external speaker(s) to the EXT.SP1
and/or EXT.SP2 jack on the rear panel {page 2}.
2 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 16.
3 Press [+]/ [–] to select 0, 1 or 2.
4 Press [MENU] to store the setting.
noitceleSuneM lennahc-L lennahc-R
0dexiMbuS&niaMdexiMbuS&niaM
1niaMbuS
2buS4/1+niaMniaM4/1+buS
If you are using an external speaker on EXT.SP2, you
can configure the transceiver to make a separate
output for each receiver.
1PS.TXE 2PS.TXE
TUPTUO
lanretnI
)L(PS
)L(1PS )R(2PS
––
√ A/NA/N
√ –
setuM √ A/N
– √
√ A/N √
√√
setuM √√
… 86 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info