606707
41
Zoom out
Zoom in
Previous page
1/77
Next page
PACKET-3
TNC COMMANDS LIST
The commands supported by the built-in TNC are listed below. You must enter a space between a command name (or short-form) and
a parameter, or between two parameters; ex. AU OFF, BEACON EVERY 18.
Command Name Short Description Parameter Default
8BITCONV 8
When ON, handles one character using 8 bits in Converse
mode. When OFF, handles one character using 7 bits.
ON/ OFF ON
AFILTER AF
Specifi es up to 4 control codes to be removed from received
packets when in Converse mode.
$00 ~ $80 $00
AUTOLF AU
When ON, sends a line feed (LF) to the computer after each
carriage return (CR).
ON/ OFF ON
AXDELAY AXD
Specifi es the delay time to be added to TXDELAY between
PTT ON and start of transmission. The unit of the parameter
is 10 milliseconds.
0 ~ 120 0
AXHANG AXH
Specifi es the voice repeater hang time. The unit of the
parameter is 100 milliseconds.
0 ~ 250 0
BEACON B
If set to EVERY, sends a beacon packet at intervals of the
specifi ed period (n). If set to AFTER, sends a beacon packet
only once after the specifi ed period (n). The unit of n is
10 seconds.
EVERY/ AFTER n
(n = 0 ~ 250)
EVERY 0
BTEXT BT
Specifi es the content of the data portion of a beacon packet.
0 ~ 159 characters
CALIBRAT CAL
Sends a space/mark square wave (50/50 ratio). Enter Q to
exit Calibrate mode and restore the Command mode.
−−
CHECK CH
Specifi es the interval from signal drop-out until execution of
disconnection. The unit of the parameter is 10 seconds.
0 ~ 250 30
CONMODE CONM
With NOMODE set to OFF, causes the TNC to automatically
enter Converse or Transparent mode when connection is
completed.
C/ T C
CONNECT C
Sends a connect request. Call1 is the callsign of the station
to be connected to. Call2 to call9 are callsigns of stations to
be digipeated through.
Call1 (VIA call2,
call3, ... call9)
CONOK CONO
When ON, accepts a connect request and returns a UA
packet. When OFF, rejects a connect request and returns a
DM packet.
ON/ OFF ON
CONSTAMP CONS
When ON, displays the current date and time when
connection is completed. The correct date and time must be
set using DAYTIME.
ON/ OFF OFF
CONVERSE
CONV
or K
Causes the TNC to enter Converse mode. Press [Ctrl]+[C] to
restore the Command mode.
−−
CPACTIME CP
When ON and in Converse mode, sends a packet at intervals
of the period determined by PACTIME.
ON/ OFF OFF
CR CR
When ON, appends a carriage return (CR) to all packets to
be sent.
ON/ OFF ON
DAYSTAMP DAYS
When ON, pressing [Ctrl]+[T] in Converse mode causes the
TNC to send date data in addition to time data.
ON/ OFF OFF
DAYTIME DA
Sets the current date and time. Enter YYMMDDhhmmss.
Sets 00 as the second if entry of the second is omitted.
−−
DAYUSA DAYU
When ON, displays the date like MM/DD/YY. When OFF,
displays the date like DD-MM-YY.
ON/ OFF ON
DIGIPEAT DIG When ON, allows the TNC to function as a digipeater. ON/ OFF ON
DISCONNE D Sends a disconnect request.
−−
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GA in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GA

Kenwood TM-D710GA User Manual - English - 55 pages

Kenwood TM-D710GA User Manual - German - 74 pages

Kenwood TM-D710GA User Manual - Dutch - 75 pages

Kenwood TM-D710GA User Manual - Dutch - 55 pages

Kenwood TM-D710GA User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info